Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFAAC Gate Access Control in Weatherford: What to Know First
We repair, replace, and upgrade FAAC gate access control systems throughout Weatherford, Texas. Most FAAC access control jobs we see, keypad replacements, photo-eye realignment, receiver board swaps, run $295 to $875 in parts and labor, with a written price in your hand before we touch a single fastener. This page is for FAAC owners in Weatherford who want to know exactly what’s failing, what it costs, and whether it’s worth fixing. If that’s you, call (940) 353-4158 and talk to a live person, any hour.
How FAAC Products Fail - and How We Fix Them
FAAC builds solid operators, but gate access control components live outside and take the full brunt of Texas heat and dust. We see the same failures across Weatherford driveways weeks after the first hard freeze or the first 100-degree stretch. Here’s what actually breaks:
- FAAC E024U control board input channels failing. The ribbon connectors from the board to the terminal block corrode, and the keypad stops talking to the board entirely. Gate won’t open from the keypad but works from the remote. We clean the pins, re-seat the ribbon, and if the corrosion is too deep, we replace the ribbon harness. The board itself usually survives.
- FAAC 455 D photocell misalignment from gate sag. On swing gates, the hinge weld stretches over years and the gate drops half an inch at the latch. That moves the photocell beam just enough to trigger the safety reversal constantly, gate opens halfway and backs up. We don’t just realign the beam; we shim the hinge to correct the drop, then align the cell. Realign without fixing the sag and it fails again in a month.
- Keypad membrane cracking from direct sun exposure. Weatherford sun breaks down the silicone membrane on FAAC keypads in about three to four years. Keys still click but the digits don’t register. We replace the membrane or install a keypad with a shade hood, and we photograph the old one before it comes out so you see what failed.
- Receiver frequency drift on older FAAC 433 MHz remotes. FAAC remotes from the XP series lose frequency lock as the internal oscillator ages. You’re standing next to the gate pressing the button and nothing happens, or it works from ten feet but not twenty. We re-tune or replace the receiver base and pair the remotes fresh. If the remote case is cracked, we replace it, OEM or a quality aftermarket equivalent, your call based on the written price.
- Capacitor failure in FAAC 400 series hydraulic pumps. The start capacitor swells in the hot months and the pump motor hums but won’t move the gate. Access control is fine, the keypad lights, the board sends the signal, and the gate ignores it. We replace the capacitor and test the pump pressure while we’re in there. A $40 capacitor saves you a $900 pump replacement.
Our FAAC Gate Access Control Process
Every FAAC job in Weatherford follows the same sequence, and you’ll see each step documented before we leave:
- 1
Inspection. We check the operator, the wiring runs, the keypad, the photo-eyes, and the receiver. We note amperage draw on the motor and test the limit switch positions.
- 2
Diagnosis in plain English. You get told what’s failed, why it failed, and what your fix options are. No jargon without a translation.
- 3
Written price. Per Haven Standard Clause 1, the flat price for parts and labor goes on paper and in your hand before work starts. You approve it, we start. You don’t, we don’t.
- 4
Parts decision. For anything directly controlling the gate travel, we recommend FAAC OEM parts to keep the factory spec intact. For peripheral items like keypads, receivers, and photo-eyes, we offer OEM or tested aftermarket equivalents, with the price difference spelled out.
- 5
Repair and calibration. We set limits, align photo-eyes, pair remotes, and test keypad codes. We run the gate through at least twenty full cycles.
- 6
Documentation. You get photos of every component we touched, the part numbers installed, and the limit-switch readings we set. We keep the same file in our records. If something shifts in January, we don’t have to rediscover this gate; the record is there.
BeforeAfterWhat FAAC Gate Access Control Costs in Weatherford
Here are the real numbers for the FAAC jobs we do most often around Weatherford:
- Keypad replacement or membrane repair: $295 to $450, depending on the keypad model and whether we’re replacing the membrane only or the full housing.
- Receiver board replacement and remote pairing: $320 to $575, including two new remotes and the time to pair existing ones.
- Photo-eye realignment with hinge correction: $185 to $410, depending on whether we’re just adjusting the beam or shimming a sagging gate.
- Full access control refresh (keypad, receiver, two remotes, photo-eyes): $825 to $1,275 on a typical Weatherford driveway gate.
What moves the price: the FAAC model on the property, the age of the wiring, whether the gate itself needs mechanical correction before the access control will hold. Estimates are free. We don’t quote over the phone sight unseen, but we’ll come out, diagnose, and put the number in writing. Call (940) 353-4158 to schedule.
Why Weatherford Homeowners Call Vance Gate Repair Weatherford for FAAC Work
We’re an independent FAAC service provider. We are not authorized by or affiliated with FAAC, and we’ve never needed to be. What we offer is a written record on every single visit. When we leave a FAAC gate in Weatherford, you have photos of the components we touched, the part numbers we installed, and the readings we set. That’s the same documentation habit Adrian Vance built on commercial access-control jobs starting in 2014, applied to residential gates.
The 365-Day Done Right Promise backs every repair: if it isn’t right, we make it right, no argument, no fee. And if your property has something other than FAAC on the gate, we service LiftMaster, Mighty Mule, Ghost Controls, and DoorKing too. We don’t steer you toward a replacement when the existing equipment still has life in it. A live person answers the phone 24/7 at (940) 353-4158.
FAQs
Yes, within limits. If your FAAC operator is still under the manufacturer warranty, we document every step, use OEM parts where the warranty requires them, and provide a written record of all work. Your warranty terms still control, but our documentation gives you the paper trail to make a claim if a covered component fails later. For machines out of warranty, we offer OEM or quality aftermarket parts with no pressure either way.
We keep the most common FAAC components in the truck: photo-eyes, receiver boards, capacitors, keypad membranes, and remote shells for the 455 D, 400, and E024U lines. Less common parts take one to three business days to arrive, and you’ll know the timeline before we order. We don’t start a job until the parts are in hand or scheduled to arrive that day.
Depends on the failure and the age of the operator. A failed capacitor, a cracked keypad membrane, or a misaligned photo-eye is a repair, and usually under $500. A flooded control board with burned traces on a twenty-year-old 400 series, that’s a different conversation, and we’ll price both the repair and the replacement in writing so you can decide on the facts. We don’t push replacements; we price both honestly.
For a gate that won’t open at all, we typically get a technician to you the same day or next morning. If your gate opens from the remote but not the keypad, that’s a scheduled call, usually within one to two days. Either way, you’ll know the technician’s name and see their photo before they arrive.
Yes. We regularly add phone entry, video intercom, and card readers to existing FAAC operators around Weatherford, including properties off the Weatherford College corridor where long driveways make phone entry especially useful. The FAAC board interfaces cleanly with third-party entry systems, and we document every wiring connection we make. Call (940) 353-4158 and we’ll tell you what’s possible with your specific FAAC model.
Written by Adrian Vance, Owner, Vance Gate Repair Weatherford at Vance Gate Repair Weatherford, serving Weatherford and nearby areas.