Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterTrusted Gate Installation for Weatherford Homeowners
Gate Installation - Weatherford means a new steel frame set in concrete, a motor wired to a dedicated circuit, and a final walkthrough with the gate swinging true before we leave the driveway. Most Weatherford installations take one full day for a single swing gate and three to five days for a double gate with new posts and an operator. We’ve installed over 22,000 gates since Adrian Vance started this company in 2014, and every one of them left with a written price agreed before the first hole was dug and a photographed record of the finished work. If you’re planning a gate in Weatherford, call (940) 353-4158 and we’ll give you the written number before you commit to anything.
We set a flat price, hand it to you in writing, and photograph what we installed before we leave. That’s the Haven Standard, and it applies to every gate we hang in Parker County, no exceptions.
What Our Gate Installation Service Includes
Every gate we install in Weatherford starts with a site check, a written scope, and a flat price. The gate itself is the visible part. The difference is in the posts, the hinges, the wire run, and the limit settings. Here’s what each type involves when we do the work.
Driveway Gate
A driveway gate spans the vehicle entrance, typically 10 to 20 feet wide, and can be a swing, slide, or lift configuration depending on the driveway slope and setback. In Weatherford, most driveways slope toward the street for drainage, which means a swing gate on a level hinge line or a slide gate with a track set above the waterline. We set the posts in concrete below the frost line, hang the gate, mount the operator if you want automation, and set the travel limits so the gate doesn’t fight the ground at the edges of the opening.
Pedestrian Gate
A pedestrian gate is the walk-through gate beside or within a larger driveway gate, usually 36 to 48 inches wide. It’s the gate you’ll use every time you check the mail or walk the dog, so the hinges and latch take more abuse than anything on the property. We hang pedestrian gates with adjustable hinges so the gate doesn’t sag in the Weatherford clay soil, and we set the latch to close positive every time.
Sliding Gate
A sliding gate travels horizontally on rollers or a cantilever track instead of swinging in or out. It’s the right choice in Weatherford when the driveway slopes steeply toward the street or when a swing gate would hit a car parked in the turnaround. We build and install slide gates with the track, the rollers, and the end stops in one scope, and we photograph the roller positions before we set the motor limits.
Swing Gate
A swing gate pivots on hinges at the posts and is the most common residential gate in Weatherford. Single swing gates up to about 14 feet are straightforward, and double swing gates cover wider openings up to 24 feet or more when the driveway needs it. We install swing gates with continuous hinges rather than barrel hinges because the continuous hinge carries the gate weight along the full post instead of two points, and it keeps a heavy gate from sagging in the first Parker County summer.
Double Gate
A double gate splits the opening in half and swings from both sides, which means two gate leaves, two hinge sets, and usually two operators if it’s automated. The extra work is in getting both leaves to close flush at the center without binding, and in Weatherford where the ground moves seasonally, that means setting the center stop and the limit switches with some travel left on the table. We set both leaves independently and test the closing sequence ten times before we call it done.
Security Gate
A security gate is a gate built for deterrence: taller, heavier steel, hardened hinge points, and often an access-control system tied to a keypad or card reader. It’s the gate you install when the driveway is long and the house isn’t visible from the road, which describes a lot of rural Weatherford addresses. We build security gates with the same commercial-grade documentation we use on access-control jobs, so you get a written record of the hinge type, the post depth, and the operator settings when we leave.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service for Gate Installation
We install and service DoorKing operators more than any other automation brand in Weatherford. DoorKing builds the motors and control boards for a lot of commercial and residential slide gates, and the service history on DoorKing units is long enough that we know exactly which control-board revisions have quirks and which ones hold settings for years. When a customer wants a new sliding gate with a DoorKing operator, we order the kit, build the gate to the spec, and set the limits with the same sequence we use on repair calls, so there’s no future guesswork.
We also install LiftMaster swing and slide operators, which are a common choice for residential driveway gates because the control boards talk to the same MyQ app many homeowners already use for their garage door. And we work on Elite and Mighty Mule units when a customer has an existing motor they want to keep. The point is the gate and the motor are two separate decisions. You shouldn’t have to buy a replacement motor just because you replaced the gate. Whether you have a DoorKing, a LiftMaster, an Elite, a Mighty Mule, or any other make, we’ll hang the gate and wire whatever motor you already own.
BeforeAfterSigns You Need Gate Installation Right Now
- The gate won’t close flush against the post. A gate that hangs an inch or two off the latch isn’t a minor annoyance, it’s a hinge or post problem that’s already started. The longer it swings partially open, the more weight the hinges carry off-axis, and the faster they wear. In Weatherford’s clay soil, a post that’s started to lean will keep leaning, and the gate will eventually scrape the ground.
- The existing gate is rusted through at the bottom rail. Water pools at the base of most gate frames, and once the bottom rail rusts through, the structural integrity is gone. You can patch it, but a patched rail is still the weak point, and a gust of wind against a full-panel gate puts real load on that exact spot. At that point the honest fix is a new gate, not another weld.
- The gate was hit by a vehicle. Even a slow bump bends the hinge posts, and a bent post means the gate geometry is wrong everywhere else. We see this in Weatherford driveways where the gate is close to the street and someone backs into it. The repair is rarely worth it when the post is moved; the new gate and new posts are the straightforward job.
- The gate is too narrow for the vehicles you now park. A single 10-foot gate works until someone buys a truck with mirrors sticking out. When every entry requires a three-point maneuver, the gate isn’t doing its job. Widening the opening and installing a new gate and operator is a clean one-week project that makes the driveway usable again.
- You’re building a new fence or replacing the driveway approach. This is the cheapest time to install a gate, because the concrete and the fence line are already open. Running gate posts and conduit before the pour is far less expensive than chipping concrete later. If the fence contractor is already out there, bring the gate in at the same time and you’ll avoid double mobilization and a messy retrofit.
Our Gate Installation Process - Step by Step
- 1
Site visit and written estimate. We come to the property in Weatherford, measure the opening, check the grade, and look at the existing posts and power. You get a written scope and a flat price that same day, before you decide anything. The written estimate is Clause 1 of the Haven Standard: the price you see is the price you pay.
- 2
Post setting and concrete work. We dig the post holes below the frost line, set the posts in concrete, and let them cure before any gate weight goes on them. In Parker County, the clay expands and contracts with moisture, so we set posts deeper than code minimums and use a concrete collar wider than the post to resist the seasonal movement that pushes posts out of plumb.
- 3
Gate fabrication and hanging. We build the gate to the opening dimensions and hang it on continuous hinges or a slide track, depending on the design. Every gate gets a level check on both axes, and we photograph the hinge points and the sag measurement before we move to the operator.
- 4
Operator installation and limit setting. If the gate is automated, we mount the motor or piston, run the wiring, and set the open and close limits with the gate under its own weight. The limit switch is set so the gate stops by the motor, not by slamming into the post. We photograph the limit positions and note the settings in the job record.
- 5
Final walkthrough and documentation. We open and close the gate ten times in front of you, verify the safety edges and photo-eye if installed, and hand you the documented record: photos of the posts, the hinges, the operator, the limit readings, and the part numbers. You also get the 365-Day Done Right Promise in writing before we pull out of the driveway.
How Much Does Gate Installation Cost in Weatherford?
For a sense of Gate Installation pricing, a single swing driveway gate with new posts and a manual latch in Weatherford typically runs $2,800 to $4,600. Add an automated operator and you’re at $4,200 to $6,800 depending on the brand and whether the power is already run. A double swing gate with two operators runs $6,500 to $11,000, and a slide gate with a track and a DoorKing operator starts around $5,500 and can go to $9,000 for a long custom span. A basic pedestrian gate runs $900 to $1,800 hung and latched.
What moves the number is the gate width, the steel gauge, the post depth, the operator brand, and whether we’re cutting concrete for the power run. A gate that’s 20 feet wide needs a heavier frame than a 10-footer, and the heavier frame needs bigger posts. A DoorKing operator and a LiftMaster operator are different prices, and we’ll show you both options in the written estimate. We avoid change orders by putting the wire run, the concrete, the gate, and the operator all in the same scope, in writing, with the flat number at the bottom.
The free estimate includes the site visit, the measurements, the grade check, and the written price. You don’t owe anything if you decide not to proceed. If you already have a written estimate from another gate company, bring it to us and we’ll review it at no cost and tell you honestly what we’d do differently. Call (940) 353-4158 for a free estimate. We’ll show you the number in writing before you commit to anything.
Gate Installation Near Weatherford - Our Service Area
We install gates throughout Parker County and the west side of Fort Worth. That includes Azle, Benbrook, Briar, Lake Worth, River Oaks, Sansom Park, Pecan Acres, Saginaw, and Crowley, along with Weatherford itself. Most Weatherford customers are inside a 30-minute drive from our dispatch point, and if you’re in one of the surrounding communities, the estimate visit is still free. We also serve Gate Installation in Azle and Gate Installation in White Settlement with the same written-price standard. If you’re near Weatherford, you’re in our service area, and the site visit doesn’t cost you anything.
Serving Weatherford, TX - Our Local Coverage Area
We’re based in the Weatherford area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked Questions - Gate Installation in Weatherford
Gate installation is the full process of setting new posts, hanging a new gate, and wiring the operator and safety devices if the gate is automated. It includes concrete work, hinge mounting, limit-switch setting, and the final documentation of what was installed. In Weatherford, a gate installation usually means a driveway gate with an operator, but it also covers pedestrian gates, double gates, slide gates, and security gates.
A straightforward single swing gate with new posts and no automation is usually a one-day job in Weatherford. A double gate with two operators and a power run takes three to five days, including the concrete cure time. We’ll give you a written schedule as part of the estimate, and the schedule is part of the scope, not a suggestion.
Most Weatherford gate installations land between $2,800 and $11,000 depending on the gate type, the width, the operator, and the power run. A basic pedestrian gate runs under $1,800, and a wide automated slide gate can exceed $9,000. Call (940) 353-4158 for a written estimate with a flat price, so you know the exact number before any work starts.
Yes. We install DoorKing, LiftMaster, Elite, and Mighty Mule operators on new gates in Weatherford, and we’ll work with whatever motor is already on the property if it’s still serviceable. DoorKing is our most-installed slide-gate operator brand because the control boards are reliable and the parts network is strong. LiftMaster is a solid residential choice when you want app control from your phone.
We keep availability for emergency replacements when a gate is down and the property is unsecured, but most gate installations in Weatherford are scheduled one to two weeks out because the concrete work and the fabrication need time. If your gate is damaged and the driveway is open to the street, call (940) 353-4158 and a live person will answer at any hour to talk through your options.
Every gate we install in Weatherford is covered by the 365-Day Done Right Promise. If anything about the installation isn’t right within that first year, we come back and make it right at no additional charge. The documentation we leave with you includes the part numbers and limit settings, so any future service uses the original install record instead of starting from scratch.
Clear the area around the existing gate or the planned opening so we have about four feet of working space on both sides. Move vehicles out of the driveway path, and let us know where any existing irrigation lines, sprinkler heads, or underground utilities run near the post locations. If the gate is automated, have a dedicated outlet within reach of the operator location or plan for us to run a circuit as part of the scope. We’ll flag any site issues in the written estimate before work begins.
Schedule Your Gate Installation Service in Weatherford Today
If you want a gate installed in Weatherford with a written price, a photo record of the work, and a one-year promise behind it, call (940) 353-4158. We’ll schedule the free site visit, hand you a flat written estimate, and never run an invoice past the number you agreed to. A real person answers the phone any hour, any day. If you’d like to see more of our work, start at our home page and browse the Gate Installation in Weatherford details before you call.
Written by Adrian Vance, Owner at Vance Gate Repair Weatherford, serving Weatherford since 2014.