FAAC Gate Installation Nationwide

FAAC Gate Installation in Weatherford: What to Know First

FAAC gate installation in Weatherford runs $1,950 to $4,850 for a complete swing-gate system including the operator, and we’re typically on site within two to three days of your call. You’ll get a written price before any work starts, and a photo record of the install when we’re done. That’s the short version. If you own a FAAC 400, 412, 770, or C720 operator and need it mounted, wired, and calibrated on a Weatherford driveway, this page tells you exactly what happens and what it costs. Call (940) 353-4158 with the model number off the side of your operator and we’ll talk it through.

Call (940) 353-4158

How FAAC Products Fail - and How We Fix Them

We see the same FAAC failures repeat across Weatherford driveways. Here’s what actually goes wrong, and what we do about it:

• FAAC 400 hydraulic pump wears out silently. The 400 series runs on hydraulic fluid, and after eight to ten Texas summers, the pump loses pressure without leaking a drop. You’ll notice the gate opening slower before it stops altogether. The fix: pump rebuild or replacement, and we photograph the pressure reading before and after so you can see the difference.
• FAAC 770 and C720 circuit boards cook in direct sun. We’ve replaced enough boards in Weatherford to know the pattern: the aluminum control box acts like an oven lid from June through September. The capacitor bulges, the gate stops mid-cycle. We install a ventilated heat shield on every exposed box we touch, even if the board is fine that day. It’s cheap insurance.
• Limit switch drift on the 412. The FAAC 412 uses mechanical limit switches, and Texas wind load pushes gates a few degrees further each season. The switch eventually reads travel as shorter than it is, the gate slams the stop, and the gear train takes the abuse. We reset the limits against a measured degree reading, not by eyeballing it, and record the setting in your file.
• Faulty aftermarket photocells cause phantom reverses. A FAAC operator expects a specific resistance value from its safety beam. Aftermarket photo-eyes from the big-box stores don’t always match, and the gate reverses for no visible reason. We test the beam with a multimeter before declaring the board dead, and we install the correct OEM or spec-matched safety edge when it matters.
• 770 capacitor failure mimics a motor problem. The C720 and 770 use a start capacitor that sits close to the transformer. When it fails, the motor hums and won’t move, which convinces a lot of owners they need a $900 motor. The capacitor is $40. We test the cap before we ever quote a motor, and we’ve saved Weatherford homeowners thousands doing exactly that.

Our FAAC Gate Installation Process

A FAAC job at Vance Gate Repair Weatherford follows the same order every time. No shortcuts, no surprises:

1. 1
   On-site diagnostic. We test your existing operator, measure gate weight and travel distance, and check the foundation mounting points. If the operator is new-in-box, we verify the model matches the gate’s duty cycle before we unbox anything.
2. 2
   Written parts decision. We quote OEM FAAC parts when the warranty matters or the operator is under three years old. For older 400-series pumps and 770 boards, we offer quality aftermarket options only where we’d put them on our own gates. The choice is yours, in writing.
3. 3
   Mechanical and electrical install. Mounting brackets, arm geometry, photo-eye alignment, and the power run. We torque to manufacturer spec and photograph every connection before the cover goes back on.
4. 4
   Calibration and load test. We set the limit switches, adjust the force settings to move the gate without strain, and run the gate through a minimum of fifteen full cycles with a vehicle in and out.
5. 5
   Documentation. Before we leave, you get a photo log showing what was found, what was set, and every part number installed. We keep a copy in our job record under The Haven Standard, Clause 4.

Before

After

What FAAC Gate Installation Costs in Weatherford

Here are real numbers, in writing, the way we quote them:

• FAAC single swing-gate install (operator included): $1,950 to $3,400
• FAAC dual swing-gate install (two operators, one board): $3,200 to $4,850
• FAAC sliding-gate operator install (770 or C720, rack and pinion): $2,400 to $4,200
• Labor only, operator supplied: $680 to $1,150 depending on gate weight and access
• Photo-eye and safety-edge replacement with calibration: $220 to $410

The price moves based on gate weight, existing foundation condition, and whether your electrical panel can handle the load. We name the price before we start, in writing. Estimates are free. Call (940) 353-4158 and we’ll come out and measure.

Why Weatherford Homeowners Call Vance Gate Repair Weatherford for FAAC Work

We show up knowing exactly which FAAC model is on your gate, because we asked before we arrived. Adrian Vance started in commercial access control, where documentation is not optional, it’s the job. That habit carried over. Every FAAC install we do gets the same written scope and photo record whether it’s a $2,000 swing gate or a $4,500 dual setup. And if your FAAC fails on day 300, the 365-Day Done Right Promise means we return and fix it at no charge. No argument, no fees. We also service LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, which matters when your gate has a mixed-brand setup and the FAAC is only one part of the problem.

FAQs