Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGhost Controls Access Control Installation: The Weatherford Owner’s Guide
Ghost Controls access control installation in Weatherford typically runs $285 to $575 installed, depending on whether we’re wiring a new keypad, card reader, or intercom into an existing Ghost Controls board or replacing the board itself. Most jobs are completed same day because we stock Ghost Controls-compatible keypads, receivers, and control boards on the truck. The usual discovery path is simple: the keypad stops accepting the code, the remote works but the keypad doesn’t, or the gate opens on its own at 2 a.m. because the access control relay stuck closed.
Name what you found, name what it costs, name what you left behind. That’s how we work, and it’s why we hand you a written price before any tool comes off the truck. Adrian Vance has been documenting gate work this way since 2014, and the habit holds on every Weatherford job.
Which Ghost Controls Models This Applies To
Ghost Controls builds its access control around two main series: the standard residential line (AXDP, REX, TSS1, and the TDS2 openers) and the heavy-duty TSS1HP for larger gates. The access control wiring on all of them runs through the GCM board on the opener, which is where most install work happens. Before we quote anything, we confirm one thing: whether your Ghost Controls unit has the optional GTO/GC remote receiver board installed or whether we’re adding it. That single detail changes the parts list by about $60.
On the OEM versus aftermarket question for Ghost Controls specifically: the genuine Ghost Controls keypad (part GTDKP) is a solid unit, but it’s not the only option that plays well with the board. We stock both the OEM part and a sealed weatherproof aftermarket keypad that holds up better in direct Texas sun. The OEM keypad membrane tends to crack around year three in Weatherford heat unless it’s shaded. If your keypad faces west, we’ll recommend the aftermarket housing with the metal face. Not because it costs less, but because we don’t want to see you again for the same failure.
We’re an independent service provider, not affiliated with Ghost Controls. We work on their equipment daily, but we’re not bound to any one parts supply chain.
Signs Your Ghost Controls Access Control Installation Is Failing
- Keypad lights up but the gate won’t move. This usually means the accessory power terminal on the control board has lost continuity, or the relay channel paired to that keypad has failed closed. We test the board with a multimeter before condemning anything.
- The gate opens randomly without a command. A sticking relay on the access control input is the common culprit, especially after a lightning storm cycles through Parker County. The relay welds itself in the open position and the board sends a phantom signal.
- Keypad works intermittently, usually worse after rain. Moisture is getting into the keypad enclosure or the wire nut connections at the base of the post. Ghost Controls keypads are weather-resistant, not weatherproof, and Weatherford downpours find the gap.
- One remote works, the other stopped. That’s a receiver memory issue, not a remote failure. The Ghost Controls board stores a finite number of transmitter slots, and older boards can drop one slot when a new device is learned in.
- The keypad beeps but the code no longer registers. The membrane contacts under the keypad face are worn. Pressing the button flexes a carbon pad against a trace; once that trace lifts, the button press never reaches the board. We replace the keypad at that point rather than chasing a solder repair on a $90 part.
BeforeAfterReplacement Cost & What’s Included
Installed Ghost Controls access control work in Weatherford breaks down like this: a basic keypad or card reader swap runs $285 to $385. Adding a new receiver or replacing a burned control board lands between $425 and $575. The range depends on how much wiring we’re replacing at the post, whether we’re adding a new enclosure, and whether the existing conduit is intact or we’re trenching a new run. You’ll see the breakdown in writing before we start, parts and labor separated.
Every access control install includes the new part, all wiring connections, programming of entry codes and transmitter slots, a full function test, and a photographed record of the final board settings and wiring layout. That photo log is yours to keep. If the problem recurs within 365 days, we make it right under the Done Right Promise. No argument, no fee, no expiration date within that window.
DIY or Call Us?
You can safely do a few checks yourself: confirm the keypad has power (the red LED should light), pop the keypad cover and look for ants or moisture, and check that the wire connections at the keypad are tight. That’s where it ends. Ghost Controls boards carry 12-volt accessory power, which won’t shock you, but a miswired relay input can smoke the board and leave you with a gate that won’t respond to anything, including the wall button.
The real risk is buying a part that doesn’t match your board revision. Ghost Controls changed board pinouts between production years, and we’ve repaired more than one Weatherford owner’s install after a generic online keypad got wired to the wrong terminal. If you’re holding a part you already bought, we’ll install it if it’s compatible, and we’ll tell you in writing if it isn’t. Call (940) 353-4158 and a live person answers.
FAQs
A Ghost Controls keypad in the Weatherford climate lasts 3 to 5 years on average, with west-facing exposure cutting that to 2 to 3 years before the membrane shows cracking. Shaded mounts on the east side of the gate post routinely last 5 years or more. For a replacement or an upgrade to a sealed metal-face unit, call (940) 353-4158.
No. Once the membrane contacts wear through or moisture gets behind the face, the keypad becomes a parts donor at best, and the repair labor costs more than a new unit. We replace the keypad and reprogram your existing codes before we leave. Call (940) 353-4158 for current pricing on the model that matches your opener.
Most Ghost Controls keypad, receiver, or control board installs in Weatherford are done in 60 to 90 minutes on site, including programming and testing. If we’re trenching a new wiring run or adding a second access point, that’s a half-day job with a written price before we dig. Call (940) 353-4158 to schedule.
Yes. Our Weatherford trucks carry OEM Ghost Controls keypads, receivers, and control boards, plus sealed aftermarket keypads and weatherproof enclosures for the Texas climate. We also stock parts for LiftMaster, Mighty Mule, and DoorKing. Call (940) 353-4158 and tell us your Ghost Controls model number, and we’ll confirm the part is on hand before we roll.
Get Your Ghost Controls Access Control Fixed Today
If your Ghost Controls gate opener is ignoring the keypad, opening on its own, or eating codes, the fix starts with a phone call to a live person at (940) 353-4158. We’ll give you a written price, a named technician with a photo before they arrive, and a documented record of what we found when the job’s done. Free estimates, upfront pricing, and the 365-Day Done Right Promise on every installed part.
Written by Adrian Vance, Owner, Vance Gate Repair Weatherford at Vance Gate Repair Weatherford, serving Weatherford and nearby areas.