Linear Gate Motor & Opener Nationwide

Linear Gate Motor & Opener in Weatherford: What to Know First

We repair and install Linear gate motors and openers across Weatherford, with most motor repairs completed in a single visit and most full motor replacements scheduled within three to five business days. A typical Linear swing-gate motor repair in Weatherford runs between $240 and $480, while a complete motor and arm replacement usually lands between $850 and $1,500, depending on the model and whether the mounting hardware survived. You’ll get a written price before we touch a fastener. If you own a Linear opener and the gate has stopped moving, is grinding, or reverses mid-cycle, call (940) 353-4158 and a live person answers.

Call (940) 353-4158

This page is for Weatherford homeowners with a Linear gate motor that is dead, weak, noisy, or unreliable. We are an independent Linear service provider, not an authorized dealer, which means we fix what is broken instead of steering you toward a replacement you may not need.

How Linear Products Fail - and How We Fix Them

Linear operators are common on Weatherford ranch-style gates, and we see the same failure patterns across the older L-Series and the newer Pro Access units. Here is what we actually find when we open the cover:

• Capacitor failure on Linear L-Series swing operators (LS050, LS070): The motor hums but the gate does not move. The start capacitor burns out after years of Texas heat cycling. We test the capacitor under load, confirm the microfarad reading is below spec, and replace it with a matching-rated unit. In Weatherford summers, a capacitor that tests marginal in spring usually dies by August.
• Limit-switch drift on Pro Access and Mighty Arm models: The gate stops short of fully open or slams past the post and bounces back. Linear’s physical limit cams wear slightly with every cycle, and after a few thousand cycles the gate overtravels. We reset the limits, verify the stall-force adjustment, and photograph the new settings so the next technician does not have to re-discover the problem.
• Gearbox wear on Linear Pro Access PGT and older HT model openers: A grinding noise under load usually means the primary reduction gear has lost teeth or the grease has broken down. On units where the gearbox is serviceable, we replace the gear and repack with high-temp grease. On sealed gearboxes, we quote a replacement before any work starts.
• Control-board corrosion from Weatherford humidity cycles: Morning dew, afternoon heat, and the occasional hard freeze stress the conformal coating on Linear control boards. We see dead boards after wet springs, especially on gates without a proper weather seal on the enclosure. We test the transformer output first, check for swollen capacitors and green corrosion on traces, and only condemn the board when the readings say so.
• Photo-eye misalignment on Linear DC models with integrated safety beams: The gate reverses immediately or refuses to close. The photo-eye, which is the infrared beam that stops the gate if something crosses the path, drifts out of alignment when the post shifts or a mower clips the housing. We realign, secure the bracket, and verify the beam interrupts cleanly at knee height and bumper height.

What matters is that we write down what we found. A Linear motor that gets fixed without a record of the original fault is a motor that gets fixed twice. We do not work that way.

Our Linear Gate Motor & Opener Process

Every Linear job in Weatherford follows the same sequence, whether it is a capacitor replacement or a full motor swap:

1. 1
   Call and dispatch: You call (940) 353-4158, a live person answers, and we schedule the visit. You get the technician’s name and photo before arrival.
2. 2
   On-site diagnostic: We remove the cover, test incoming voltage, check the capacitor and transformer, inspect the gearbox and limit assembly, and run the motor through a full open-close cycle if it will move at all.
3. 3
   Written price: Before any repair, you get a written scope and a flat price. If we find a second problem while inside the unit, we stop and get your approval with a new written price. No surprise invoice follows us out the driveway.
4. 4
   Parts decision: For wear items like capacitors, belts, and limit switches, we use OEM Linear parts or equivalent-grade aftermarket parts rated to the same spec. For control boards and gearboxes, we recommend OEM because the aftermarket copies do not hold up to Texas heat. You decide, but you decide with a written recommendation.
5. 5
   Repair and test: We replace, adjust, and then run the gate through a minimum of ten open-close cycles, including an obstruction test and a force test. If it does not pass, we do not call it done.
6. 6
   Documentation and cleanup: We photograph the finished work, the new settings, and the part numbers installed. You get that photo log and a written record before we leave. Under Clause 4 of the Haven Standard, that documentation is included on every visit at no additional charge.

Before

After

What Linear Gate Motor & Opener Costs in Weatherford

Here is what we quote for common Linear scenarios in Weatherford. These are flat written prices, not hourly estimates.

• Capacitor replacement: $240-$320
• Limit-switch reset and adjustment: $180-$260
• Photo-eye realignment or replacement: $220-$380
• Gearbox repair on serviceable units: $380-$550
• Full Linear swing-motor replacement (arm, motor, and mounting hardware): $850-$1,500
• Linear slide-motor replacement: $900-$1,800, depending on the track condition and whether the chain or belt drive needs replacement too

What moves the price is the model, the condition of the mounting brackets and gate hardware, and whether the control board can be reused. A gate that has been sagging for two years wears out a new motor fast, so we quote hinge and wheel work separately when the gate itself is the root cause. Estimates are free, and the written price is handed to you before any work begins.

Why Weatherford Homeowners Call Vance Gate Repair Weatherford for Linear Work

Adrian Vance started this company in 2014 after years of commercial access-control work, and the habit of documenting every wire, every reading, and every part number never left. We bring that same discipline to residential Linear operators in Weatherford, out past the Weatherford College corridor and into the ranch neighborhoods where driveway gates run hard and the summers punish electronics. Our technicians work on nine major automation brands, including LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, so if your property has a mixed setup or you are considering a brand switch later, we can tell you honestly what works and what does not. Every job carries the 365-Day Done Right Promise: if the repair is not right within a full year, we make it right at no charge. Name what you found, name what it costs, name what you left behind.

FAQs