Linear Gate Repair Nationwide

Linear Gate Repair in Weatherford: What to Know First

Linear gate repair in Weatherford typically runs $165 to $480 for most board, limit-switch, and receiver jobs, with motor replacements landing between $540 and $920 depending on the model. Most Linear repairs are completed same-day once we’re on site, and we service the full linear actuator and swing-gate lineup including the LRA series, the APeX controller, and older MegaCode receivers. You get a written price before any work starts, not after.

Call (940) 353-4158

This page is for Weatherford homeowners with a Linear gate that stopped, reversed mid-travel, beeps but won’t move, or opened on its own at 3 a.m. If that sounds familiar, call (940) 353-4158 and a live person answers. We’re an independent Linear service provider, not a factory-authorized shop. That independence matters because we repair Linear equipment instead of steering you toward a replacement.

How Linear Products Fail - and How We Fix Them

Linear gates fail in patterns. Once you’ve seen a few hundred of them across Weatherford driveways, you know what to look for before the cover comes off. These are the failures we write up most often:

• APeX controller board relay failure. The Linear APeX is a solid controller, but the onboard relays that drive the motor wear after years of Texas heat cycling. The gate will hum or click without moving, or it’ll open but refuse to close. We test the relay contacts with a meter, confirm the failure, and replace the board with an OEM unit or a quality aftermarket equivalent if the owner wants to save money. The part number goes on your invoice, photographed before we leave.
• LRA series actuator limit-switch drift. Linear’s LRA linear actuators use mechanical limit cams that can slip over time, especially on heavy iron gates that slam into the stops. The gate over-travels, the motor strains, and then the thermal cutoff trips. We reset the limits to factory spec, run a full cycle test, and photograph the new position settings. That photo goes in your job record and saves the next technician from re-diagnosing the same drift.
• MegaCode receiver ghost activations. The MegaCode rolling-code receiver is generally reliable, but weather intrusion through a cracked housing can cause phantom openings. We’ve had Weatherford customers call because their gate opened by itself during a thunderstorm. The fix is usually a new receiver board and resealing the housing gasket, not replacing the whole opener. We solder in the new board, reprogram the transmitters, and test with the old remotes to confirm every code still works.
• Photoelectric eye misalignment on LRA swing arms. The photo-eye (the infrared beam that stops the gate if something crosses the path) on LRA swing installations mounts to the gate post and the fence line. Clay soil shifts across Weatherford, and the post moves a half inch, and suddenly the gate refuses to close because the beam is broken. We realign the eyes, shim the bracket if the post has shifted permanently, and log the beam alignment in the record.
• Worn drive gears in older Linear swing operators. On Linear’s earlier swing-gate models still running in Weatherford, the nylon drive gear inside the gearbox strips after years of pushing gates that were never properly balanced. You’ll hear the motor run but the gate won’t budge, or it’ll chatter. We rebuild the gearbox where parts are still available, and where they aren’t, we tell you straight up and give you a written price for a replacement operator with no pressure to buy it today.

Our Linear Gate Repair Process

Every Linear job follows the same sequence. It’s not complicated, but it is disciplined, and that discipline is why the price rarely changes between the estimate and the invoice.

1. 1
   Call and dispatch. You call (940) 353-4158, a person answers, and we schedule a technician. You get the tech’s name and photo before arrival. No anonymous van pulls up.
2. 2
   On-site diagnosis. The technician opens the operator cover and tests the board, limits, receiver, and motor. We check the gate itself too, because a dragging hinge will destroy a new Linear motor just as fast as it destroyed the old one.
3. 3
   Written price. Before any tool touches a fastener, you get a written scope and flat price for the repair. That’s Haven Standard Clause 1. If you want to compare it to another estimate, bring us the paperwork and we’ll review it free.
4. 4
   Parts decision. We tell you whether OEM Linear parts are available and what they cost, and whether a quality aftermarket part will perform the same for less. You choose. The part number is printed on the invoice either way.
5. 5
   The repair and test. We install, set limits, program transmitters, and run the gate through at least five full open-close cycles while observing stop points, beam interruption response, and motor draw. If something’s not right, we fix it before we leave.
6. 6
   Documentation handoff. You get a photo log of what was found, what was adjusted, what was installed, and what the test showed. We file the same record internally. That’s the 365-Day Done Right Promise backing every job.

Before

After

What Linear Gate Repair Costs in Weatherford

Here are honest numbers for the most common Linear repairs we write up in Weatherford. These are flat prices quoted before work begins, not hourly estimates that creep upward.

• Limit switch reset and adjustment: $165 to $240, including the test cycle and photo documentation.
• MegaCode receiver board replacement: $185 to $320 depending on the board revision and whether it’s single or dual channel.
• APeX controller board replacement: $280 to $475 for OEM, $220 to $310 for quality aftermarket.
• Photo-eye realignment or replacement: $150 to $260 for alignment, $190 to $340 if we’re installing a new photo-eye pair.
• LRA actuator motor replacement: $540 to $920 depending on actuator length, gate weight, and whether the arm bracket is still intact.
• Full operator replacement (Linear to Linear): $1,100 to $1,850 installed, including new operator, arms, transmitter programming, and the full documentation package.

What moves the price: part availability, gate weight, post condition, and whether corrosion has spread into the brackets. What doesn’t move the price: surprise line items at the end. The written price is the price. Estimates are free. Call (940) 353-4158 and we’ll put it on paper.

Why Weatherford Homeowners Call Vance Gate Repair Weatherford for Linear Work

Most gate companies can swap a board. What they don’t do is hand you a written scope before the job and a photographic record when it’s done. That’s the difference Adrian Vance built into this company starting in 2014, and it’s the reason Weatherford customers call us when their Linear gate quits.

We service nine gate-automation brands including Linear, LiftMaster, Mighty Mule, Ghost Controls, and DoorKing. That matters because when a Linear actuator fails and the repair quote is close to the cost of a different operator, we can give you honest numbers on all your options instead of steering you toward the one brand we happen to sell. Every repair is covered by the 365-Day Done Right Promise: if it’s not right, we make it right, no argument, no fee. A live person answers the phone 24/7. And before the technician arrives, you know their name, their face, and what the service call will cost.

Name what you found, name what it costs, name what you left behind. That’s how we’ve always worked, and it’s how every Linear job in Weatherford gets handled.

FAQs