Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Everman
New gate installation and Gate Repair in Everman typically runs $1,800 to $6,400 depending on whether we’re hanging a single swing gate, a double driveway gate, or a sliding gate with automation. Most standard single driveway gates are installed in one day. If you call (940) 353-4158 before noon, we can usually have a technician at your Everman property the same day to measure, write a firm price, and schedule installation. We work all over Everman, from the neighborhoods off W Enon Avenue to the streets around J.E. Marr Park and Everman High School, and we’ve spent years reading this city’s clay soil and 1950s-era fence lines as much as its hardware.
Why Vance Gate Repair Weatherford Is Everman’s Preferred Gate Installation Company
Most of the gates we hang in Everman go into yards where the original gate was installed when the house was built, sometime between the 1950s and the 1980s. That means we’re usually working with corroded hinge posts, shallow footings, and fence lines that haven’t been square in a decade. Our team, led by Adrian Vance, started in commercial access-control work in 2014, and that background shaped how we document residential jobs. Every installation in Everman comes with a written price before we touch anything and a photo record when we leave. Under The Haven Standard, Clause 4, you get a documented photo log of what we found, what we set, and what we installed, no extra charge.
The reason Everman homeowners keep our number is simple: we don’t hand over a verbal estimate and a handshake. We hand over a written scope, a written price, and a record of the work. That matters for a job like gate installation, where the second fear after the breakdown is an invoice that doesn’t match the quote. Our price is quoted and agreed before any work starts. If a post footing turns out worse than expected once we dig, we stop, show you what we found, and write the revised number down. You decide. No surprises at the end.
We answer the phone with a live person 24 hours a day. No voicemail loop, no callback queue. That matters when a gate has failed and your driveway is wide open at 11 p.m. Dispatch for Everman is coordinated from our Dallas-Fort Worth office, and we keep Everman jobs local, with crews that know W Enon Avenue, Oak Grove, and the older blocks around Bishop Street without needing directions.
From the Gate Installation team to the technician who shows up with your name and photo texted before arrival, you’ll know who you’re dealing with. Our techs are background-checked and uniformed. And if anything on the installation isn’t right, our 365-Day Done Right Promise means we make it right within a full year, no argument, no fee.
Our Gate Installation Services in Everman
We focus our Everman work on the gate types this city actually has: driveway gates, pedestrian gates, sliding gates, and swing gates. Here’s what that looks like on the ground.
Driveway Gate Installation
A driveway gate in Everman is usually a single or double swing on tubular steel or chain-link posts that were set 18 to 24 inches deep. Modern code wants 30 to 36 inches with a concrete collar. When we install a new driveway gate here, we don’t just swap panels. We assess the post depth, check for clay heave, and if the footing is too shallow, we reset it before hanging the new gate. That’s the difference between a gate that stays plumb through August and one dragging the ground by Labor Day. Most single driveway gates in Everman run $1,800 to $3,200 installed, automation separate.
Pedestrian Gate Installation
Pedestrian gates in Everman take a beating because they’re the gate people actually use daily. The latch, hinges, and post connections fail long before the panel does. We install walk gates with welded steel frames, adjustable hinges, and a latch that won’t bind when the post shifts half an inch on Fort Worth Clay. A standard pedestrian gate here runs $600 to $1,400 depending on width, metal gauge, and whether the existing post is reusable. If it’s not, we replace the post and collar it properly.
Sliding Gate Installation
Sliding gates make sense on Everman lots where the driveway slopes or where a swing gate would block a parking area. The tradeoff is that a sliding gate needs a level track, a heavier frame, and usually a loop detector or photo-eye system so it doesn’t close on a car. Sliding gate installs in Everman run $2,800 to $6,400 for a standard residential opening, with automation and safety sensors included. That’s a bigger number, but you’re getting a gate that won’t sag on clay that moves 2 to 4 inches a season, because the track carries the load rather than a hinge post.
Swing Gate Installation
Swing gates are what most Everman driveways already have, and they’re the gate type we hang most often here. A new swing gate should be built on posts set 30 inches deep with a concrete collar, with hinges rated for the panel weight and an opener matched to the swing arc. We install FAAC, LiftMaster, and DoorKing swing operators regularly in Everman, and we set the limit switches and photo-eyes before we call the job done. A single swing gate with new posts and non-automated hardware runs $1,800 to $3,800; add automation and you’re typically at $3,200 to $5,500.
Double Gate Installation
Double gates are common on Everman corner lots and homes with wider driveways. The failure mode we see most is post spread: the two hinge posts lean away from each other as the clay expands and contracts, and the meeting stiles no longer align. When we install a double gate, we often run an underground tension bar or a thicker gauge hinge post to resist that spread. Double gate installs in Everman range from $3,400 to $6,400 with hardware, depending on opening width and whether we’re automating one or both leaves.
Security Gate Installation
A security gate in Everman isn’t necessarily ornamental. It’s often a heavier steel frame with a keypad, a maglock or electric strike, and photo-eyes set to stop the gate if anything crosses the beam. We install these with a written wiring diagram on completion, matching what Adrian Vance developed on commercial access-control jobs before he started this company. Security gate installations here fall between $4,000 and $7,500 depending on the operator, access control hardware, and whether we’re adding a telephone entry post at the curb.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterTrusted Brands We Service in Everman
Everman gates run everything from brand-new DoorKing and Elite operators to 1990s control boards that predate modern safety sensor standards. We install and service nine automation brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. That matters because we won’t steer you into replacing a working motor just to sell a different brand. If a Mighty Mule operator is on the gate and it’s sound, we quote the installation around it. If the control board is obsolete and can’t support photo-eyes or loop detectors, we’ll name that plainly and give you a written price to retrofit. We keep common boards, hinges, brackets, and photo-eye sets stocked for fast turnaround in Everman.
Common Gate Installation Problems We See in Everman Homes
These are the four failure modes we see most often when we show up to install or replace a gate in Everman:
- Shallow-set hinge posts on Fort Worth Clay: A post set 18 inches deep in 1972 moves 2 to 4 inches vertically in a wet-dry cycle. That’s why a gate that was plumb in April drags the ground by September. Fixing it means removing the old post, augering to 30-plus inches, and pouring a concrete collar. Single-visit fixes without deeper post work are rare.
- Corroded hinge welds on aging tubular steel: Everman’s original gates are often 40 to 60 years old. The hinge weld is the first place moisture gets in, and once the weld splits, the gate panel sags regardless of what you do to the latch. At that point we usually replace the panel rather than trying to weld a rusted tube.
- Obsolete control boards: A 1990s swing operator can’t talk to modern photo-eyes or loop detectors. Homeowners often want to add safety sensors, and we have to tell them the board won’t support it. A full operator retrofit is the only honest answer, and we write that up with the part number and board photo before we start.
- Gates hung before safety standards existed: Many Everman gates predate UL 325 requirements for entrapment protection. When we install a new gate or retrofit an old one, we include photo-eyes or an edge sensor so the gate stops and reverses if something crosses the path. That’s not optional equipment for us. It’s what makes a gate legal to automate.
Pricing for Gate Installation in Everman, TX
Here’s what gate installation actually costs in Everman, based on the work types we handle in this city:
- Pedestrian gate, steel frame, new hinges and latch: $600 to $1,400
- Single driveway swing gate, new posts and non-automated hardware: $1,800 to $3,800
- Single swing gate with automation (operator, photo-eyes, keypad): $3,200 to $5,500
- Double driveway gate, new posts and hardware: $3,400 to $6,400
- Sliding gate, track, automation, safety sensors: $2,800 to $6,400
- Security gate with access control: $4,000 to $7,500
The spread comes down to opening width, metal gauge, whether we’re setting new posts or reusing existing ones, and what automation brand goes on. Every quote includes the written price before work starts. If you’ve got a written estimate from another company, bring it to us. We’ll review it at no cost and tell you honestly whether the scope matches the number. Call (940) 353-4158 for a free measure and written estimate in Everman.
Everman’s Clay Soil Is the Real Story Behind Gate Installation
You can’t talk about gate installation in Everman without talking about what’s under the gate. Fort Worth Clay is a shrink-swell soil. It absorbs water through the wet winters and spring rains, expands, and pushes against everything embedded in it. Then the summer drought hits, the clay cracks and contracts, and the soil drops. A post set 18 to 24 inches deep rides that movement like a piston. It heaves up in spring and settles unevenly in fall. The gate hangs on that post. So a gate that clears the ground by four inches in April can drag the concrete by September, not because the hinges failed, but because the post moved. We’ve measured 2 inches of heave on a single year on Everman properties. Modern code requires 30 to 36 inches of post depth with a concrete collar, and the difference is functional, not cosmetic. Our crews set posts to that depth by default here, because we know what happens if we don’t.
A job on Little School Road sticks with us. We replaced a corroded tubular-steel swing gate where the original 1972 post footing had heaved 2 inches out of plumb after the spring rains. Our crew reset the hinge post on a deeper concrete footing with a 2-foot collar, hung a new FAAC swing operator with safety photocells, and added a keypad entry. The gate cycles clean now, even after the clay cracks each summer. That’s the standard we apply to every gate installation in Everman. It’s not enough to hang a straight gate on a moving post.
We Also Serve Cities Near Everman
Our gate installation crews regularly work in Everman and the surrounding Tarrant County communities, including Weatherford, Azle, White Settlement, and Benbrook. The same written-price policy and documented photo record apply whether we’re setting a new driveway gate in Everman or servicing a swing gate in Azle. Call (940) 353-4158 and we’ll route the nearest technician to your property.
Serving Everman, TX - Our Local Coverage Area
We’re based in the Everman area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Installation in Everman
It’s almost always the post, not the gate. Everman sits on Fort Worth Clay, which heaves and settles 2 to 4 inches per season. If your hinge post was set 18 to 24 inches deep, it moves with the soil, and the gate drags a few weeks after being re-hung. The permanent fix is resetting the post to 30-plus inches with a concrete collar. Call (940) 353-4158 and we’ll measure the post depth and tell you straight whether a reset will hold.
Yes, if the control board supports them. Many 1990s-era boards can’t run modern photo-eyes or edge sensors, and we’ll tell you that on the first visit. If the board can handle it, we install the photo-eyes, set the beam height, and test the reverse function before we leave. If it can’t, we write up a full operator retrofit with the price and part number. Estimates are free.
Usually, yes. Loop detectors keep a sliding gate from closing on a vehicle in the driveway. They also let the gate open automatically as a car approaches. On Everman’s clay, loop wires need to be saw-cut into the concrete or buried with a stable bedding so ground movement doesn’t sever the wire. We install both loop detectors and photo-eyes on sliding gate jobs, and the price is in the written quote before we start. Call for a free estimate.
If the hinge posts are leaning away from each other but the panels are sound, resetting the posts usually fixes the alignment. We dig out the old posts, auger deeper, pour a concrete collar, and re-hang the same panels. If the panels are corroded at the welds or the framing is bent, replacement is cheaper than repeated repairs. We’ll show you photos of what we find before recommending either path.
Sag correction means restoring a gate panel to level when it has dropped at the latch side, usually due to hinge wear or a failed weld. On older Everman gates, if sag correction has been done more than once, the underlying frame is usually fatigued and a new panel is the better money. We’ll tell you which applies after we inspect the hinges and the frame. The estimate is free, and the price is written before any work starts.
Written by Adrian Vance, Owner at Vance Gate Repair Weatherford, serving Everman and Tarrant County since 2014.