Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Everman, TX
Gate access control and parts-and-welding work in Everman almost always starts with the same finding: a gate that has been asked to do its job on hardware that predates the current homeowner and the current phone system. Most Everman properties are mid-century ranch homes with chain-link or tubular-steel gates that have never once had a hinge pin lubricated, a post checked for plumb, or a limit switch verified. The clay soil does the rest. Call us at (940) 353-4158 and we’ll show you what we mean, in writing and with photos, before any tool comes off the truck.
Why Everman Homes Are Different
Everman sits on Fort Worth Clay, the same shrink-swell soil that defines southern Tarrant County. The clay expands through wet winters and springs, then cracks and contracts through every summer drought. That movement lifts and settles gate posts by two to four inches over a single season. A gate that was plumb after last spring’s repair can be dragging the ground by September, not because the hinges failed but because the post itself heaved out of position.
The housing stock compounds the problem. Everman’s residential streets are lined with ranch homes built mostly between the 1950s and 1980s. The original fence posts were often set shallower than what modern code would permit, and the original gate hardware is frequently still in service. Technicians here regularly find hinges corroded through, frames bent from years of dragging, and hardware that has never been lubricated. Budget-conscious ownership patterns mean the gate gets pushed, pulled, and propped open rather than serviced. By the time we arrive, the repair is rarely a single-part fix. It is usually a small sequence: reset the post, replace the hinge, retune the operator if one exists, and document all three so the next service call starts with evidence instead of guesswork.
Our Main Everman Services
Three services account for most of the gate work we do across Everman. Each has its own detailed page with pricing, sub-jobs, and what to expect.
Gate Repair in Everman
Repair work here usually means correcting what the clay soil and time have done to an old gate: realigning the frame, replacing corroded hinges, cutting and re-welding a sagging rail, or resetting a post that has heaved out of plumb. We photograph the misalignment before we touch it, then document the corrections so the record is clear. See Gate Repair in Everman for pricing and sub-job detail.
Gate Installation in Everman
New gates in Everman should be set on posts that go below the active clay zone, with concrete that accounts for the soil’s seasonal movement. Chain-link, tubular steel, and ranch-style wood gates all have different anchoring requirements here. We quote the full job in writing, including post depth and concrete type, before any digging starts. See Gate Installation in Everman for the full scope.
Gate Motor & Opener in Everman
Operator work on Everman gates often reveals motors that were installed years ago and never adjusted since. Limit switches drift, photo-eyes get knocked out of alignment, and control boards fail in the heat. We service nine major brands, so the motor already on your gate is usually repairable rather than destined for the landfill. See Gate Motor & Opener in Everman for what that involves.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterGate Access Control in Everman
Gate access control in Everman means adding or repairing the systems that decide who can open the gate: keypads, remotes, phone entry, card readers, and video intercoms. The older the gate, the more likely the original access hardware was either never installed or added piecemeal over the years, then left to corrode in Tarrant County humidity and heat. This service is part of our Gate Access Control work, and every job leaves you with a written record of what was set, replaced, and programmed.
Keypad Entry
Signs you need it
The keypad is cracked, sun-bleached, unresponsive to some digits, or the code stopped working after a power outage.
What it costs in Everman
Keypad replacement on an existing gate typically runs $185 to $420, wiring and reprogramming included.
How we do it
We remove the old keypad, check the low-voltage wiring for corrosion, install the new unit on a weather-sealed mount, then program and test your codes before we record the settings.
Remote Control
Signs you need it
Remotes work only from close range, intermittently, or not at all while the keypad still opens the gate fine.
What it costs in Everman
Replacing or adding remotes runs about $45 to $95 per remote, plus $85 to $150 to re-sync the receiver.
How we do it
We test the receiver’s antenna and frequency, replace or reprogram remotes as needed, and photograph the new transmitter settings for your record.
Phone Entry
Signs you need it
Visitors or delivery drivers cannot call in without a keypad code and you want the gate opened from your phone.
What it costs in Everman
A basic phone-entry controller replacement runs $425 to $830, system and programming included.
How we do it
We wire the controller to the existing operator or install a cellular bridge if there is no landline, then walk you through the dial-in and open function before documenting the programming.
Video Intercom
Signs you need it
You want to see and speak with whoever is at the gate before you press the open button.
What it costs in Everman
Video intercom systems for a single gate typically run $850 to $1,850, camera, monitor, and power supply included.
How we do it
We mount the camera at gate-facing height, run low-voltage cable or configure wireless, pair the indoor monitor, and verify two-way audio and video before leaving you the settings sheet.
What Gate Access Control Costs in Everman
| Item | Typical range in Everman |
|---|---|
| Keypad replacement or install | $185 - $420 |
| Remote programming or replacement | $45 - $150 |
| Phone entry controller | $425 - $830 |
Can you retrofit access control to an old Everman gate?
Yes. Most mid-century chain-link gates accept a keypad, remote receiver, or intercom without replacing the gate itself. We run new low-voltage wiring and anchor the hardware to the existing post or frame, then test everything before we finish.
Does the access system fail during hot Everman summers?
Heat-related failures are common on older boards and keypads with degraded seals. Replacing weather gaskets and installing UV-stable housings fixes most of it. Call (940) 353-4158 for a written quote on your specific system.
Gate Parts & Welding in Everman
Parts and welding work in Everman usually means rescuing a gate that has sagged, seized, or broken loose from its own post. The steel on these mid-century gates is often thick enough to salvage, but the hinges, rollers, and brackets around it are usually rusted beyond reuse. Our Gate Parts & Welding work replaces the failed components and welds the frame back to square, then leaves you with photos of every cut and bead.
Hinge Replacement
Signs you need it
The gate drags on the latch side, the hinge pin is visible bent or seized, or the gate tilts noticeably when it swings.
What it costs in Everman
Hinge replacement on a typical Everman gate runs $85 to $240 per gate, hinges and labor included.
How we do it
We cut or unbolt the failed hinges, realign the gate to the post, weld or bolt on new hinges sized to the gate weight, and photograph the final position before we test the swing.
Post Replacement
Signs you need it
The post leans or has lifted out of the ground, the gate no longer closes, or concrete at the base is cracked and shifting.
What it costs in Everman
Post replacement with concrete in Everman’s clay soil starts around $320 and can go to $700 depending on depth and size.
How we do it
We core out the failed post, auger the hole below the clay movement zone, set a new post in deeper concrete, and document the depth and alignment before rehanging the gate.
Rail Repair
Signs you need it
The top rail is sagging or bowed, the gate frame is out of square, or the latch no longer lines up with the receiver.
What it costs in Everman
Rail repair or replacement typically costs $120 to $310, depending on rail length and whether welding is required.
How we do it
We cut out the bent section, weld in new steel matched to the frame profile, grind the joints smooth, and recheck the gate for square before recording the work.
Gate Rollers
Signs you need it
The gate screeches, demands force near the end of travel, or the roller wheel has worn through its axle.
What it costs in Everman
Roller replacement for sliding or rolling gates typically runs $65 to $180 per roller assembly.
How we do it
We inspect the track for damage, replace the roller with a weight-rated match, adjust the gate level, and document the old-part condition and the new part number.
What Gate Parts & Welding Costs in Everman
| Item | Typical range in Everman |
|---|---|
| Hinge replacement | $85 - $240 |
| Post replacement with concrete | $320 - $700 |
| Rail repair | $120 - $310 |
Can you weld a broken gate instead of replacing it?
Usually, yes. Most Everman gates are tubular steel or chain-link frames that weld cleanly. We quote the repair against a replacement in writing before any work starts, and you choose with both numbers in front of you.
Is welding covered under your warranty?
Welding repairs fall under the 365-Day Done Right Promise like any other completed work. If the weld fails within a year, we return and make it right at no charge. Call (940) 353-4158 for details on a specific job.
Brands We Service in Everman
We service Mighty Mule, LiftMaster, FAAC, and BFT equipment, plus five other major automation brands. Common Everman gates run older Mighty Mule and LiftMaster openers, and we keep their parts stocked locally so a control-board replacement does not wait on a distributor. See our brands for the full list and the parts we carry.
Pricing for Gate Repair in Everman, TX
| Service | Typical range in Everman |
|---|---|
| Keypad replacement | $185 - $420 |
| Remote programming or replacement | $45 - $150 |
| Phone entry controller | $425 - $830 |
| Video intercom system | $850 - $1,850 |
| Hinge replacement | $85 - $240 |
| Post replacement with concrete | $320 - $700 |
| Rail repair | $120 - $310 |
| Gate roller replacement | $65 - $180 |
Everman pricing runs higher when clay movement has thrown a post far enough out of plumb that the gate needs both a post reset and a frame correction. The written price you receive before any work starts is the price you pay, under Haven Standard Clause 1.
Neighborhoods We Serve in Everman
We work across Everman’s residential streets, including the older ranch-home pockets near the center of town and the perimeter lots that see the heaviest clay movement. Response time across the city usually runs under 90 minutes for repair calls.
- Everman city center ranch neighborhoods
- Areas west of Everman Parkway
- East Everman near the railroad line
- Perimeter lots along Oak Grove Road
- Subdivisions near the Everman school campus
Service Area - Cities Near Everman
We also handle gate work in the surrounding southern Tarrant County cities, including Weatherford, TX, Azle, TX, White Settlement, TX, and Benbrook, TX. Crews are dispatched from our Dallas-Fort Worth office and serve Everman locally without a separate service trip.
Serving Everman, TX - Our Local Coverage Area
We’re based in the Everman area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Everman
Most Everman repair calls get a technician on site within 90 minutes. We answer the phone live at (940) 353-4158 around the clock, and a written price is produced before any work begins, so the dispatch does not commit you to a surprise invoice.
Most repairs and part replacements in Everman do not require a permit. New installations or post work sometimes need approval, especially on corner lots or near utility easements. We check local requirements as part of the written quote and handle the paperwork when it applies.
Our 365-Day Done Right Promise covers the work we completed, including post re-sets and re-welds. If the gate shifts within a year due to a post we set, we return and fix it at no additional charge. Seasonal clay movement is exactly what the warranty is built to answer.
Call (940) 353-4158 for a free estimate on any gate repair, access control, or welding job in Everman. A live person answers, the written price comes before any work starts, and the photo record is yours to keep.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Everman Customers Say
"They installed the opener and left me a diagram of the wiring and the limit settings. When I needed a second remote programmed I could do it myself."
- Nadine C."Our gate was hit by a delivery truck. They came out, documented the damage properly for the insurer, and the claim went through without an argument."
- Camille R."Honest about what did not need doing. Told me the operator had years left and only the control board needed replacing."
- Douglas N.