Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Motor & Opener Across Everman
Gate motor and opener repair in Everman usually runs between $240 and $680 for common failures like stripped gears, dead capacitors, or misaligned safety beams. Most repair calls are completed the same day we arrive, since our trucks carry boards, arms, and limit switches for the brands most common on this side of Tarrant County. If you’re in Everman and your gate won’t open, drifts off track, or reverses for no reason, call (940) 353-4158 and a live person answers, day or night.
We know Everman’s gates specifically. The ranch homes east of Everman Parkway and around Johnson Park were built when gate hardware was simple and posts were shallow. They don’t fail the way a 2015-era swing operator in a new subdivision fails. They fail because the clay moved, the post leaned, the arm bound up, and the board finally gave out. That distinction matters when we price a repair, because fixing the motor isn’t enough if the post that carries it isn’t stable.
Why Vance Gate Repair Weatherford Is Everman’s Preferred Gate Motor & Opener Company
Most of our Everman work starts with a phone call from a homeowner who already checked the fuses, already reset the breaker, and already read the manual. They describe the symptom precisely, and that tells us they want straight answers, not a sales pitch. That’s exactly how we operate. Adrian Vance built this company in 2014 out of commercial access-control work, where every service call required a written record of what was found and what was changed. We carry that same habit to every residential driveway in Everman.
Before any work begins, you get a written price. Not a verbal range, not a “we’ll see when we get in there.” A flat, written scope and price handed to you before a tool comes off the truck. That’s Clause 1 of The Haven Standard, and it applies to every gate motor job we do in Everman. When the job is done, you get a photo log of what we adjusted, what part we installed, and what the final limit-switch settings were. No other gate company serving Everman documents work this way.
We also answer the phone 24 hours a day. Not an answering service, not a voicemail box. A live person. If your gate motor dies at 11:45 on a Saturday night and the gate is stuck half-open across your driveway, you’ll get a real conversation and a plan, not a callback window.
Our Gate Motor & Opener Services in Everman
Motor Installation
A new motor install in Everman starts with a written quote that includes the operator, the arm or rack, the power run, and the condition of the posts that will carry the load. We don’t bolt a $700 motor onto a post that’s leaning 4 degrees out of plumb and call it done. If the post needs attention, the quote includes it. On most ranch-style Everman properties, a complete swing motor installation with a name-brand operator runs $1,450 to $2,800 depending on gate weight, post condition, and whether we’re adding battery backup.
Motor Repair
Motor repair is the bulk of our Gate Motor & Opener work across Everman. When a motor hums but won’t turn, or trips its breaker, or grinds when the gate reverses, we diagnose the specific failure, not the general category. A stripped plastic gear in a Mighty Mule runs $180 to $320 to replace. A failed capacitor runs $140 to $240. A burned control board on an older FAAC or LiftMaster runs $380 to $650, and we’ll tell you honestly whether that board is worth replacing on a motor that’s 20 years old. Sometimes it is. Sometimes the cheaper long-term answer is a new operator with a warranty.
Linear Motor
Linear motors are simple machines that fail in predictable ways, and most of those ways trace back to alignment. In Everman, alignment is a moving target. The clay swells, the post shifts, the rack and pinion start binding, and the motor works harder every cycle until something strips. We set linear units with the gear lash specified by the manufacturer, then photograph the final setting. If the same unit drifts again in three months, the photo tells us whether it’s the operator or the ground under it. Linear motor service in Everman typically runs $180 to $420 for adjustments and component repairs, and $900 to $2,100 for replacement units with rack.
Slide Motor
Slide motors on Everman’s older properties usually fail because the gate itself wasn’t built for automation. The original gate worked fine as a manual slider for 40 years, because a person could muscle it past a slightly deformed track. A motor can’t. We check the rail, rollers, and end stops before we ever blame the operator. Slide motor replacement in Everman runs $1,200 to $2,600, including rail adjustment and safety edges where required.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterTrusted Brands We Service in Everman
We service the equipment already on your property rather than steering you toward whatever brand we happen to sell. LiftMaster, Mighty Mule, FAAC, BFT, and six other major automation brands are covered by our stock and our training. For Everman customers, that means we almost always have the common boards, remote receivers, and arm parts for your specific operator on the truck the first trip. We won’t sell you a new opener because we’re out of a $40 limit switch.
Common Gate Motor & Opener Problems We See in Everman Homes
- Clay heave pushing the post out of plumb. Wet winters swell the Fort Worth Clay under Everman’s shallow post footings, and a gate that ran true in April binds the operator arm by July. This is the single most common root cause of motor failures in Everman. The motor was fine; the ground under it moved.
- Legacy control boards failing from moisture. 1990s-era swing operators on Everman’s older homes often had electronics enclosures that were never sealed against Tarrant County humidity. Condensation builds up every cool night, and eventually the board corrodes. We see this constantly on original equipment around the streets west of Johnson Park.
- Safety reverse tripping for no visible reason. Misaligned photo-eyes on a gate whose posts shifted an inch or two will trip the closing reverse repeatedly. The beeping isn’t a bad motor. It’s the beam telling you the two ends of the gate no longer line up.
- Gear wear from continuous binding. When a slide gate motor fights a track that’s out of alignment for a full season, the nylon gears inside the operator are the sacrificial part. They’re designed to strip before the motor burns, but that doesn’t make the repair feel any less sudden when the gate stops 18 inches short of closed.
Pricing for Gate Motor & Opener in Everman, TX
| Service | Typical Range in Everman |
|---|---|
| Motor repair (capacitor, gear, limit switch) | $180 - $420 |
| Control board replacement | $380 - $650 |
| Photo-eye alignment or replacement | $140 - $260 |
| Swing motor installation (complete) | $1,450 - $2,800 |
| Slide motor installation (complete) | $1,200 - $2,600 |
| Linear operator replacement | $900 - $2,100 |
| Battery backup installation | $300 - $550 |
These are the ranges we’ve actually billed on recent Everman jobs. What moves the number is post condition, gate weight, wire-run distance, and whether the existing arm or rack can be reused. Every quote is written and handed to you before we start, with the exact parts and labor broken out line by line. If you have a written estimate from another company, we’ll review it at no cost.
Call (940) 353-4158 for a free estimate. The price you’re quoted is the price you pay, in writing, before work starts.
We Also Serve Cities Near Everman
Our crews dispatch to Everman daily from the Dallas-Fort Worth area, and we also serve Gate Motor & Opener in Everman neighbors in Weatherford, Azle, White Settlement, and Benbrook. The soil in those towns varies, but the gate problems are familiar. Call and tell us where you are and what the gate is doing.
Serving Everman, TX - Our Local Coverage Area
We’re based in the Everman area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Motor & Opener in Everman
Yes, in most cases. A dragging gate on an Everman property is usually the post leaning, not the concrete failing. We can often correct up to 2 to 3 degrees of lean by mechanical realignment at the hinge side, without cutting or re-pouring. If the post has heaved beyond that, the honest answer is that a deeper footing is the only permanent fix, and we’ll show you the measurements that justify it before you spend a dollar. Call (940) 353-4158 and we’ll tell you which category your gate is in.
More often than you’d expect. A 40-year-old chain-link gate with a decent frame can carry a new LiftMaster or FAAC operator fine, provided the hinges are solid and the post is stable. We’ve retrofitted modern swing arms onto plenty of 1970s-era tubular gates around Everman Parkway and the streets north of it. The decision comes down to the condition of the welded corners and the depth of the post footing, not the age of the gate.
Usually the soil. The photo-eye at the gate’s far end is mounted to a post that’s been moving with the Everman clay, while the operator post has moved differently. The beam drifts off target and the opener reads it as an obstruction. We realign the beams and, when needed, reposition the sensor mount so it can tolerate the normal seasonal shift. The motor is typically fine in this scenario.
If the operator is from the 1990s and the board got wet, probably not, and we’ll tell you that before we sell you anything. A replacement board for an obsolete unit can cost $300 to $500 and leaves you with a motor that’s still 30 years old. In most Equipman cases, the smarter spend is a new operator with a sealed enclosure and a warranty, installed for $1,450 to $2,800. But we’ll show you both numbers in writing and let you decide.
Sometimes, yes. If the existing footing is intact but just too shallow for the clay’s seasonal movement, we can stabilize the post by extending the footing at depth without tearing out the old concrete entirely. We auger around the existing post, pour a deeper collar, and mechanically tie the two together. It’s not a band-aid, but it’s also not magic. If the old concrete is cracked through, re-pouring is the only repair that lasts, and our quote will reflect the difference honestly. Call (940) 353-4158 and we’ll assess it in person.
A Local Problem You Won’t Hear About From a National Chain
Everman’s post-war fence posts were often set shallower than modern code requires, in a type of clay that moves 2 to 4 inches vertically every season. That number matters more than any spec on a motor box. A freshly plumb swing operator installed in April can be dragging its arm against the ground by September, not because the motor failed, but because the post it’s mounted to rose out of the dirt. No amount of limit-switch adjustment fixes that. The fix is mechanical: cut the post, auger deeper, set it in a footing that reaches below the active shrink-swell zone, and re-hang the gate. We do this work on Everman properties regularly. It costs more than a motor swap, but it’s the only repair that stops the same failure from returning every wet season.
We learned this lesson the hard way, or at least documented it thoroughly. In the Town East subdivision, we replaced a 1980s-era chain-link swing gate operator on a ranch home where the hinge post had heaved so badly the arm had snapped its mounting bracket twice. We cut the post at ground level, augered a new footing 18 inches deeper than the original, re-hung the gate, and retrofitted a LiftMaster LA400 with a battery backup. The homeowner had been propping the gate open every time a summer storm knocked the power out. Now it runs on a motor with a documented installation record, in a post that doesn’t move.
That’s what separates a gate motor job in Everman from a gate motor job anywhere else. Here, the operator is only half the problem. The ground under it is the other half, and a company that doesn’t understand Fort Worth Clay will keep selling you the same repair every 12 months. We document everything, price it in writing, and stand behind it for 365 days under the Done Right Promise. If the repair isn’t right, we make it right, no argument and no additional charge.
Written by Adrian Vance, Owner at Vance Gate Repair Weatherford, serving Everman homeowners with written pricing, documented photo records, and gate automation expertise since 2014.
Gate Motor & Opener in Nearby Areas
