Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Benbrook, TX
Gate access control in Benbrook runs into two problems more often than anywhere else in Tarrant County: heavy equestrian gates on shifting clay, and 1970s-1990s ranch properties where the original wiring has outlived its insulation. A keypad or intercom that works fine in River Oaks stops reading cards or drops calls here because the post has tilted four degrees and pulled the low-voltage conduit apart. Call (940) 353-4158 and we’ll put a written price in your hand before any tool comes off the truck.
Why Benbrook Homes Are Different
West of Winscott Road, Benbrook stops acting like a suburb. The lots widen, the zoning turns horse-friendly, and the gates change from decorative steel to something closer to ranch infrastructure: 300 to 500 pound pipe-and-tube swing gates on posts the clay is actively moving. Tarrant County’s Vertisol soil swells through wet winters and shrinks in 100°F summers, and a post that was plumb in March can be an inch and a half off by August. That tilt is what kills keypads, shears hinge welds, and strips the gear on an opener that was perfectly aligned when it was installed. Add 40-plus years of heat on powder-coated iron and you get peeling finishes and rusted-through bottom rails. Benbrook isn’t a harder place to work. It’s a place where the usual failure modes happen faster and heavier.
Our Main Benbrook Services
These are the two service categories Benbrook homeowners call about most. Each has its own page, but here’s the short version so you can see where your problem falls.
Gate Repair in Benbrook
Hinge weld sheared off a heavy ranch gate, roller seized on a chain-link slide, post leaning far enough that the latch misses the receiver. We reset, reweld, realign, and replace. Tarrant clay demands post work here more than in any neighboring city. Gate Repair in Benbrook
Gate Installation in Benbrook
New gate on an existing opening, or a full opening built fresh. In Benbrook the question is usually weight: an equestrian gate needs a heavier frame, deeper post embedment, and an operator sized for the load. We measure, quote in writing, and schedule. Gate Installation in Benbrook
Gate Motor & Opener in Benbrook
The motor is running but the gate barely moves, or the opener stripped its gear against a post the clay pushed out of line. We service the motor you already own across nine brands rather than steering you to a replacement. Gate Motor & Opener in Benbrook
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterGate Access Control in Benbrook
Access control on a Benbrook gate means electronics mounted to a structure the ground is moving. A keypad that worked in May reads “error” in September because the gate post tilted and pulled the wiring harness just enough to break a solder joint inside the unit. Older ranch properties carry systems from the 1990s, and their insulation is brittle. We handle Gate Access Control as a repair-first practice: diagnose the actual fault, show you the reading, and fix what failed rather than replacing the system by default.
Keypad Entry
Signs you need it
Codes work intermittently, the backlight fails, or the keypad reads every code as invalid after a cold snap.
What it costs in Benbrook
Keypad replacement in Benbrook typically runs $140-$260 installed, depending on whether the wiring survived and the post is plumb.
How we do it
We test the old unit’s voltage at the terminals, replace or re-terminate the wiring, mount the new keypad, program your codes, and photograph the final installation.
Card Reader
Signs you need it
The reader beeps but won’t release the gate, or it works for some cards and not others after a storm.
What it costs in Benbrook
Card reader replacement runs $260-$520 installed, with the spread driven by whether we can reuse your existing card format or need to reissue credentials.
How we do it
We verify reader output with a meter, check the power supply, swap the unit if confirmed dead, re-enroll cards, and leave you a written record of the reader model and wiring map.
Video Intercom
Signs you need it
Audio works but video shows static, calls drop at the indoor station, or the outdoor unit has gone white from UV and you can’t see who’s there.
What it costs in Benbrook
Video intercom replacement in Benbrook runs $400-$900 installed, depending on wiring condition and whether you’re running a single or dual station.
How we do it
We test continuity from the outdoor unit to the indoor station, replace failed components, reseal the outdoor housing, and photograph the final setup at both ends.
What Gate Access Control Costs in Benbrook
| Item | Typical range in Benbrook |
|---|---|
| Keypad replacement | $140-$260 |
| Card reader replacement | $260-$520 |
| Video intercom replacement | $400-$900 |
Can you fix my access control the same day in Benbrook?
Usually yes. We carry replacement keypads, card readers, and common intercom boards on the truck, so most Benbrook access-control calls are fixed in one visit. Call (940) 353-4158 and we’ll confirm while you’re on the phone.
Do I need to replace the whole system if my keypad fails?
No. Roughly half the access-control failures we see in Benbrook are wiring faults from post movement, not failed electronics. We diagnose first, show you the fault, and replace only what’s actually dead.
Gate Parts & Welding in Benbrook
Benbrook’s gate inventory runs heavy because the properties do. Ranch-style pipe-and-tube swing gates out west of Winscott Road weigh hundreds of pounds, and when the clay moves a post, that weight becomes a lever working against the hinge welds. We do structural repair and custom welding in Benbrook with the same documentation standard we use on every job: photos of the break, photos of the repair, and a written part number for anything we install. See Gate Parts & Welding for the full scope.
Hinge Replacement
Signs you need it
The gate drags on the latch side, the top hinge gap widens, or you can see daylight through a cracked weld at the hinge barrel.
What it costs in Benbrook
Hinge replacement runs $60-$150 per hinge installed, with heavier weld-on barrel hinges for equestrian gates at the top of that range.
How we do it
We cut or unbolt the failed hinge, grind the mounting surface clean, weld or bolt the new hinge in place, and photograph the finished weld before the gate ever hangs on it.
Post Replacement
Signs you need it
The post leans visibly, the gate sags toward the latch even after hinge work, or the post base is rusted through at ground level.
What it costs in Benbrook
Post replacement in Benbrook typically runs $280-$650 per post, including concrete, depth for the gate’s weight, and realignment of the gate on the new post.
How we do it
We dig out the old post and its footing, set the new post in concrete at the correct depth for the gate weight, brace it until set, then rehang and realign the gate.
What Gate Parts & Welding Costs in Benbrook
| Item | Typical range in Benbrook |
|---|---|
| Hinge replacement | $60-$150 per hinge |
| Post replacement | $280-$650 per post |
| Weld repair (crack or break) | $120-$300 |
Can you weld my gate in place, or does it need to come off?
Most weld repairs in Benbrook are done in place; we only remove the gate when the break is at a point we can’t access safely with the gate hung. The written quote specifies which before we start.
How long does a welded hinge repair last on a Benbrook gate?
On a properly reset post, a welded hinge repair should last the life of the gate. The variable in Benbrook is the post, not the weld. We’ll tell you if your post needs work first, and why. Call (940) 353-4158 for a written price.
Brands We Service in Benbrook
We work on LiftMaster, Mighty Mule, FAAC, and BFT equipment already installed on Benbrook properties, plus the rest of the nine major automation brands we service. Common boards, remotes, and safety eyes for these brands are stocked on our trucks, so most repairs in Benbrook don’t wait on parts. See our brands.
Pricing for Gate Repair in Benbrook, TX
| Service | Typical range in Benbrook |
|---|---|
| Keypad replacement | $140-$260 |
| Card reader replacement | $260-$520 |
| Video intercom replacement | $400-$900 |
| Hinge replacement | $60-$150 per hinge |
| Post replacement | $280-$650 per post |
| Weld repair (crack or break) | $120-$300 |
| Gate roller replacement | $40-$100 per roller |
| Rail repair | $150-$400 |
Two things push price up in Benbrook: gate weight and post condition. An equestrian gate that’s heavier than standard drives the hinge and post work to the top of the ranges. Every quote is written and handed to you before work starts, with the exact scope and the exact price.
Neighborhoods We Serve in Benbrook
We cover all of Benbrook, with most calls coming from the acreage properties west of Winscott Road and the ranch neighborhoods near Benbrook Lake. Typical response time anywhere in the city is the same day for most repairs.
- Westpark
- Whitestone
- Timbercreek
- Mira Vista
- Benbrook Lake area
Service Area - Cities Near Benbrook
Vance Gate Repair dispatches crews from our Dallas-Fort Worth office to Benbrook and the surrounding cities. We also serve Weatherford, TX, Azle, TX, White Settlement, TX, and Briar, TX with the same written-price standard.
Serving Benbrook, TX - Our Local Coverage Area
We’re based in the Benbrook area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Benbrook
Most Benbrook repairs are dispatched same day. We carry common gate parts, access-control components, and welding gear on the truck, so the first visit usually completes the job. Call (940) 353-4158 and you’ll speak with a live person, any hour.
Some Benbrook HOA-governed neighborhoods require architectural approval for a gate replacement or a finished change, but repair of existing equipment generally does not. We’ll flag when approval is likely needed, and we’ll work from the written scope they require.
Yes. The larger equestrian lots along the western edge of Benbrook are a regular route for us, and we’re set up for heavy pipe-steel gates and ranch-style openers that most suburban crews don’t see. Response time there is the same as the rest of Benbrook.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Benbrook Customers Say
"They installed the opener and left me a diagram of the wiring and the limit settings. When I needed a second remote programmed I could do it myself."
- Nadine C."Our gate was hit by a delivery truck. They came out, documented the damage properly for the insurer, and the claim went through without an argument."
- Camille R."Honest about what did not need doing. Told me the operator had years left and only the control board needed replacing."
- Douglas N.