Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Motor & Opener Across Benbrook
Gate motor repair in Benbrook usually costs $180 to $640, depending on whether we’re replacing a gear, a control board, or the entire operator. Most repair calls get same-day or next-day service from our Dallas-Fort Worth dispatch office, and we carry parts for FAAC, BFT, Linear, and Viking on the truck. If your gate won’t open, stalls halfway, or trips its breaker every afternoon, call (940) 353-4158 and we’ll give you a straight answer on the phone, not a callback window.
Benbrook is different from the tighter Fort Worth suburbs next door. West of Winscott Road and down toward Benbrook Lake, we work on ranch-style pipe-and-tube steel swing gates that weigh 300 to 500 pounds. Those gates are hard on motors. They’re also sitting on Tarrant County clay that heaves and tilts posts every wet winter and dry summer. That combination is exactly what our Gate Motor & Opener team was built to handle.
Why Vance Gate Repair Weatherford Is Benbrook’s Preferred Gate Motor & Opener Company
We started as a commercial access-control shop in 2014, and Adrian Vance brought that same documentation habit to every residential driveway gate we touch. In Benbrook, we see the same failure patterns repeat across neighborhoods: stripped gear tracks on slide gates along Stevens Road, burned control boards in the 1970s-1990s ranches east of Winscott, and sagging 400-pound swing gates on the equestrian lots near the lake. Because we document every visit with photos and written measurements, when we come back we know exactly what we did last time. No second diagnosis fee for the same problem.
Our Benbrook customers get a written price before any tool comes off the truck. That’s Haven Standard Clause 1, and it’s not negotiable. We also back every completed repair with our 365-Day Done Right Promise: if the gate motor acts up within a year, we make it right at no charge. A live person answers our phone 24/7. You won’t get a voicemail loop at two in the morning when your gate is stuck open and the horses are on the wrong side of the fence.
Our Gate Motor & Opener Services in Benbrook
We work on whatever motor is already on the property. We don’t steer you toward a replacement if a repair makes more sense, and we don’t sell you a brand you don’t need. Here’s what we handle most often in Benbrook.
Motor Repair
Motor repair is our most common Benbrook call, and it usually starts with an overload trip on a swing gate that’s heavier than the operator was rated for. We diagnose the actual failure: a stripped gear, a failed capacitor, a limit switch that’s drifted, a control board that cooked in the summer heat. Then we show you the part, explain what it does, and write the price down before we replace it. If the motor is salvageable, we repair it. If the gear train is destroyed, we’ll tell you, and we’ll photograph the damage so you can see it for yourself.
Motor Installation
When an old operator has been rebuilt twice and the control board is discontinued, replacement is the cheaper answer. We install new swing and slide gate motors on Benbrook properties of every size, from the ornamental iron gates in the 1970s subdivision cores to the heavy ranch gates west of Winscott. Every installation follows the same standard: written scope, written price, photo log when we leave. We never surprise you with an invoice at the end.
Linear Motor
Linear-brand piston or in-ground motors are common on Benbrook properties, especially on heavier custom gates. The 300-500 pound pipe-steel gates near Benbrook Lake put a real load on linear drives, and we stock Linear gears, capacitors, and control boards locally so we’re not waiting on a parts shipment when your gate is down. We also handle the in-ground hydraulic box replacements that some older Benbrook estates still run.
Slide Motor
Aging slide gates from the 1980s and 1990s are everywhere in Benbrook, usually on chain-link or ornamental iron frames with track rollers that have been grinding for decades. The motor may be fine, but a seized roller or a bent track will make it trip its breaker every time. We replace rollers, straighten track, reset limit switches, and install new slide motors when the old one has finally given up. Then we align the safety photo-eyes so the gate stops and reverses like it should.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterCommon Gate Motor & Opener Problems We See in Benbrook Homes
- Clay-heaved posts throwing operators out of alignment. Tarrant County’s Vertisol clay swells in wet springs and shrinks in the July heat, pushing fence posts several inches off plumb in a single season. A gate that’s suddenly binding, grinding, or tripping the breaker usually has a post that moved, not a motor that failed.
- Equestrian-scale gates overloading residential motors. Those 300-500 lb pipe-and-tube steel swing gates on the horse properties west of Winscott Road and down near the lake were never matched to the right operator. The motor’s overload circuit trips constantly, or the gear strips, or the control board burns out from repeated thermal stress. The fix is often a heavier-duty operator plus hinge reinforcement, not another residential board.
- Obsolete control boards dying in Benbrook summers. Operators installed in the 1980s and 1990s are now hitting 30-40 years of service. The control boards inside weren’t built for decades of >100°F heat, and many replacement boards are discontinued. We can often retrofit a modern board with UL 325 safety compliance into an older housing, keeping the original motor if it’s still sound.
- Sheared hinge welds on heavy swing gates. When a 400-pound gate leans on a hinge that was welded 20 years ago, the weld eventually gives. The gate drops, binds, and strips the gear track on the motor in one afternoon. We see this consistently on Benbrook’s larger-lot equestrian properties, and it usually requires post resetting, hinge replacement, and a full motor re-rig.
Pricing for Gate Motor & Opener in Benbrook, TX
Here’s what you can expect to pay in Benbrook. We quote every job in writing before we start, and that written figure is the figure you pay. No percentage added at the end, no “while we were here” extras.
| Service | Typical Benbrook Range |
|---|---|
| Control board replacement | $280 – $520 |
| Gear replacement (swing or slide operator) | $180 – $380 |
| Limit switch reset or replacement | $120 – $240 |
| Full swing gate motor replacement (residential) | $650 – $1,400 |
| Heavy-duty operator for 300-500 lb equestrian gate | $1,200 – $2,600 |
| Post reset in new concrete footing | $450 – $900 |
| Battery backup installation | $320 – $680 |
| Full slide gate motor replacement | $700 – $1,850 |
These are honest ranges for Benbrook work. The final number depends on the gate’s size and weight, the condition of the posts and hinges, and whether the existing operator can be retrofitted or needs full replacement. We never charge for a second opinion on a written estimate from another company. Bring us the paperwork and we’ll review it free. Call (940) 353-4158 to schedule a service visit, and we’ll put a written price in your hand before any work begins.
Trusted Brands We Service in Benbrook
We service and install FAAC, BFT, Linear, and Viking operators, plus five other major automation brands. If your Benbrook gate was installed before you bought the property and the motor has a nameplate you don’t recognize, we can identify it, source parts, and keep it running. We stock common gears, capacitors, boards, and safety photo-eyes for FAAC and Linear locally, because those two brands show up most often on the ranch-style gates in Benbrook’s western neighborhoods. We don’t push replacement when the motor has life left in it.
We Also Serve Cities Near Benbrook
Our gates and openers coverage extends from Benbrook through Weatherford, Azle, White Settlement, and Briar. If you’re on the western edge of Benbrook near the lake or off Winscott Road, we’re already in your neighborhood every week. Dispatch is coordinated from our Dallas-Fort Worth office, and we route Benbrook calls to the nearest available technician.
Serving Benbrook, TX - Our Local Coverage Area
We’re based in the Benbrook area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Motor & Opener in Benbrook
It’s usually the post, not the motor. A 400-lb gate hanging on a post that Tarrant County clay has pushed off plumb will bind at the hinge, and that binding force makes the motor draw more current than its overload circuit will allow. The motor trips because it’s working against a misaligned gate, not because the motor is weak. We reset the post in concrete, rehang the gate level, and then test the motor under real load before recommending anything else. Call (940) 353-4158 and we’ll diagnose it on site.
Yes, in most cases. If the motor is still sound, we can fit a modern control board with UL 325-compliant safety inputs, install photo-eyes and edge sensors, and keep the original motor and housing. That saves anywhere from $800 to $2,200 compared to a full slide operator replacement. We’ll photograph the old board, wire the new one into the same enclosure, and give you a written record of the part numbers installed. If the motor is shot, we’ll tell you that plainly and give you a replacement price before anything happens.
Install a battery backup on the operator. A quality battery backup system for a residential Benbrook gate runs $320 to $680 installed, and it keeps the gate cycling for several days of intermittent use or 10-20 full cycles during a single outage. On the western edge of the county, where summer outages are more common, we add battery backups to most heavy gate installations as standard. You can still open the gate manually with a release key during a total outage, but battery backup means you don’t have to get out of the truck.
Not directly, but it’s a warning sign. Failing powder coat means exposed steel, and exposed steel on a Benbrook gate means rust at the hinge points and latch. Rusted hinges create drag, and drag makes the motor work harder and burn out sooner. Refinishing the gate and replacing worn hinge bearings is far cheaper than replacing a burned-out motor later. We see this consistently on 1980s and 1990s ornamental iron gates across Benbrook’s older subdivisions, and we’ll flag it during any motor inspection.
Sheared hinge welds stripping the gear track on the operator. A heavy pipe-steel gate drops a few inches when a hinge weld fails, and that drop misaligns the gear, strips teeth, and overloads the motor in seconds. We saw this last month on a property off Stevens Road west of Winscott, where a 400-lb swing gate on a LiftMaster LA400 had torn the gear track apart because the 6×6 wooden post had been pushed off plumb by clay heave. We reset the post, rehung the gate with reinforced hinges, replaced the gear and limit switches, aligned the photo-eyes to UL 325, and added a battery backup. The total was under $1,200, and the gate has cycled clean ever since.
If your gate motor is struggling, stalling, or tripping in Benbrook, call (940) 353-4158. You’ll get a live person, a straight answer, and a written price before we touch a single bolt.
Written by Adrian Vance, Owner at Vance Gate Repair Weatherford, serving Benbrook since our founding in 2014.