Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Benbrook
If you’re searching for Gate Repair in Benbrook because a heavy swing gate won’t close or a chain-link slide gate has jammed halfway, here’s the direct answer: most hinge and post repairs in Benbrook run between $425 and $1,400 depending on the post footing, and automatic opener repairs typically fall between $275 and $800. We dispatch technicians from our Dallas-Fort Worth office directly to Benbrook neighborhoods, and a live person answers the phone at (940) 353-4158 around the clock. You’ll get a written price before any work begins, so the figure we quote is the figure you pay.
Benbrook is not a typical suburban gate market. The horse-friendly zoning west of Winscott Road and the acreage parcels near Benbrook Lake mean we work on gates that weigh three to five times what a standard ornamental driveway gate weighs. That changes how we diagnose, how we price, and how we build the repair.
Why Vance Gate Repair Weatherford Is Benbrook’s Preferred Gate Repair Company
Our Gate Repair team has worked on more than 22,000 gates since 2014, and a meaningful share of those jobs sit along Benbrook’s western edges, where a single gate repair often involves a 400 lb pipe-steel panel, a failing post, and an operator that has been fighting the load for years. Adrian Vance came out of commercial access-control work, and that’s the standard we apply to every residential gate in Benbrook: a written scope, a written price, and a photo record of everything we touched before we leave.
Benbrook homeowners tend to ask the same questions: Can you fix the post without replacing the whole gate? Will the repair hold through one of Tarrant County’s wet winters? What does this cost in writing? We answer all three on the first visit. Under Haven Standard Clause 4, every Benbrook job includes a documented photo log: the found condition, every adjustment we made, and the exact part numbers installed. You keep the record. No future technician has to guess what was done.
Our Gate Repair Services in Benbrook
Electric Gate Repair
Electric gate repair in Benbrook usually means diagnosing an operator that either won’t respond, cycles partway, or throws an error light and stops. We service the opener brands already installed on Benbrook properties, including LiftMaster, FAAC, Mighty Mule, BFT, and Ghost Controls. We do not steer you toward a replacement motor just because it’s older. A limit-switch reset or a new photo-eye (the infrared beam that stops the gate if something crosses the path) often fixes what looks like a dead opener, and we’ll photograph the reading before and after the adjustment.
Automatic Gate Repair
On Benbrook acreage, automatic gates get abused. A 450 lb pipe swing gate puts stress on every component, and when the post leans, the operator’s gear track strips because it’s pushing against a gate that no longer swings on its intended plane. We check the operator, the arm bracket, the power source, and the post alignment as one connected system. If you have no electrical service at the gate end of a long driveway, we regularly configure solar gate openers with battery backup, a setup we see constantly off Winscott Road and along the southern edges near Benbrook Lake.
Hinge & Post Repair
This is the Benbrook-specific repair we do more than any other company in the area mentions. Tarrant County’s Vertisol clay soil shrinks in summer and swells in wet winter months. A wooden or thin-walled steel post set in that soil moves, often several inches over a single seasonal cycle. We dig out the old footing, set the post deeper with a concrete collar, re-weld the hinge barrel, and photograph the final plumb reading. The repair is built for the soil, not just the gate.
Gate Realignment
A Benbrook gate that drags, scrapes, or closes with a gap at the latch is usually a post that has shifted, not a gate that was hung wrong. Gate realignment means resetting the geometry: horizontal and vertical alignment at the hinges, latch throw and strike adjustment, and operator travel limits. We do this after the post is stable, because realigning a gate on a moving post is a repair that lasts about two weeks.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterTrusted Brands We Service in Benbrook
We maintain and repair nine gate-automation brands, which means the motor already on your Benbrook property is likely one we know well. LiftMaster and FAAC are the most common openers we see on residential and acreage swing gates in the area. Mighty Mule and BFT also appear frequently on DIY-installed and rural setups. Our trucks carry a working inventory of control boards, limit switches, photo-eyes, and remotes for these brands, so a Benbrook repair call usually finishes in a single visit rather than waiting on a shipped part.
Common Gate Repair Problems We See in Benbrook Homes
- Leaning hinge posts on heavy pipe gates. The combination of a 300-500 lb gate and Tarrant County shrink-swell clay pushes thin-walled steel or wood posts off plumb in one season. The first visible sign is usually a torn top hinge weld or a gate that scrapes the ground.
- Stripped operator gear tracks on equestrian swing gates. When the post leans, the opener keeps pulling on a gate that’s no longer swinging true. It strips the rack-and-pinion or gear track. We reset the post first, then replace or re-time the operator.
- Jammed chain-link slide gates from the 1970s-1990s build era. Benbrook’s core housing stock includes ranch homes from those decades, and their aging slide gates seize on rusted rollers and bent tracks. Roller replacement, track straightening, and motor service usually bring them back.
- Powder-coat delamination and weld-point rust on iron and aluminum gates. North Texas summer UV and 100°F heat break down the coating, then clay-soil moisture accelerates rust at every weld and hinge point. We repair the steel, then refinish and seal the affected sections.
Pricing for Gate Repair in Benbrook, TX
We publish Benbrook price ranges on the page because you should know the number before you call. Hinge and post repair on a standard swing gate in Benbrook runs $425-$1,400 depending on whether the post is set in clay and needs a new concrete collar. Gate realignment alone runs $175-$400. Automatic opener repair, including limit-switch resets, photo-eye replacement, and control-board work, runs $275-$800. Weld and rust repair on a pipe-steel equestrian gate runs $350-$1,200 depending on how many hinge and frame points need new steel. Every job we quote in Benbrook gets a written price before work starts, and the number you sign is the number you pay. Call (940) 353-4158 to schedule a free estimate.
Off Winscott Road, our tech found a 450 lb ranch pipe swing gate with its hinge post leaning 4 inches out of vertical from clay swell. The shear had torn the top hinge weld and stripped the rack and pinion on a LiftMaster LA400 operator. We set a new deep post footing with a concrete collar, re-welded the hinge post, and realigned a solar gate opener with battery backup. The gate now swings true through the next big rain.
We Also Serve Cities Near Benbrook
Our Benbrook customers often refer us to family and neighbors in nearby areas. We provide the same written-price, photo-documented Gate Repair service across Weatherford, Azle, White Settlement, and Briar. If your property is on the edge of Benbrook or just across a county road, call (940) 353-4158 and we’ll confirm coverage.
Serving Benbrook, TX - Our Local Coverage Area
We’re based in the Benbrook area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Repair in Benbrook
Because Tarrant County’s expansive Vertisol clay soil swells when wet, and the swelling pushes shallow or undersized post footings out of vertical, especially under a heavy 300-500 lb pipe gate. A post set without a deep concrete collar will move again the next wet season. The permanent fix is a deeper footing with a concrete collar sized for the gate’s weight, which we do on acreage properties west of Winscott Road and near Benbrook Lake all the time. Call (940) 353-4158 if you’d like a written estimate.
Yes, and this exact failure shows up regularly on Benbrook acreage. The stripped gear track is usually the symptom, not the cause. The post underneath has shifted from clay heave, and the operator has been pulling against a gate that no longer swings true. We reset and collar the post first, then repair or replace the rack-and-pinion so the operator is working on a stable gate. A written price comes before any work, and you get a photo record of the whole repair. Call (940) 353-4158 to set up the visit.
Yes. A large share of Benbrook’s western acreage gates run on solar power with battery backup because running mains power to the gate end of a long driveway is impractical. We service solar gate openers, diagnose battery and panel issues, and replace or re-time operator components on solar setups. If the current solar setup can’t keep up with the gate’s cycle rate, we’ll spec the panel and battery capacity the gate actually needs, in writing, before any change is made. Call (940) 353-4158 for a free on-site look.
If the post has moved, resetting it is always the better repair. A slide gate that’s arcing is usually caught between a shifting post and a track that has also moved. Re-welding the panel without resetting the post means the next soil cycle undoes the weld. We reset the post with a proper concrete collar, then straighten or replace the track, then deal with the panel. It costs more than a quick weld, but it’s the repair that stays repaired. Call (940) 353-4158 and we’ll assess it on site.
Yes, automatic gates in Texas are required to have entrapment protection, which usually means at least one reversing mechanism such as a photo-eye or contact edge, depending on the gate type and installation date. On every automatic opener service call in Benbrook, we inspect the entrapment protection, test it, and photograph the result as part of the documented record we leave with you. If the gate fails the test, we’ll quote the fix in writing. Call (940) 353-4158 to schedule.
Written by Adrian Vance, Owner at Vance Gate Repair Weatherford, serving Benbrook and surrounding Tarrant County communities since 2014.