Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterTrusted Gate Parts & Welding for Weatherford Homeowners
Gate parts and welding in Weatherford usually comes down to one of two jobs: a hinge or post has failed and the gate now drags, or a section of steel has cracked and needs to be cut out and replaced. Most Weatherford homeowners call us after a gate has already started scraping the driveway or pulling away from the post. We repair the gate where it stands, replace the failed part with something matched to the existing steel, and hand you a written price before any work begins. Since 2014, Adrian Vance and the team at Vance Gate Repair have completed over 22,000 gate repairs and installations, each one documented with photos and a written record of what was found, what was changed, and what it cost. If your gate is dragging, sagging, or separating at the welds, call (940) 353-4158. A live person answers, day or night, and we can usually have a technician in Weatherford the same day.
What Our Gate Parts & Welding Service Includes
Hinge Replacement
Gate hinges carry the entire weight of the gate every time it opens, and in Gate Parts & Welding in Weatherford‘s clay soil the post can shift just enough to transfer that load into the hinge barrel instead of the post itself. When you see the gate drop half an inch at the latch side or hear a groan when it moves, the hinge is usually the first thing we check. We cut out the old hinge, weld in a replacement matched to the gate’s weight and steel thickness, and photograph the finished weld before we leave. The written report you get includes the hinge part number, the weld position, and the gap measurement at the latch, so you can see exactly what was corrected.
Post Replacement
A leaning gate post is rarely a hinge problem; it is a footing problem, and Azle Gate Parts & Welding customers see the same expansive soil issue. When the post has shifted more than a few degrees, no hinge adjustment will hold the gate level for long, so we dig out the old footing, set a new post in concrete, and brace it plumb while it cures. We also weld a new hinge plate to the post if the original plate is bent or cracked. Before we pour, we record the post depth and concrete volume in writing, and you receive a photo of the excavation and the set post before the gate is rehung.
Rail Repair
The top and bottom rails on a steel gate are what keep the pickets straight and the gate square under repeated cycling. When a rail cracks, usually at a weld joint where the picket meets the rail, the gate begins to rack, and the latch stops lining up with the post. We cut out the cracked section, grind the surrounding steel clean, and weld in a replacement section of matching gauge and profile. If the crack is stress-related rather than impact-related, we also check for a misaligned hinge or a sagging post that might re-crack the same joint.
Custom Welding
Some Weatherford gates cannot be repaired with an off-the-shelf part because the original builder fabricated a one-off bracket, or the gate has a curved top rail that no catalog part matches. For these, we weld the part to spec in the field or in our shop, matching the original steel profile and paint prep so the repair blends with the gate. A custom weld is also the practical fix when a gate was originally built with a weak point, like a thin-wall tube hinge bracket that has already bent once. We measure, cut, weld, and photograph the new part, and the written record shows the exact dimensions so the next repair, if it ever comes, starts from that drawing.
Gate Rollers
Sliding gates ride on rollers, and in Weatherford the fine grit that blows off driveways works its way into the roller bearings and grinds them out. A roller that has seized stops rolling and starts dragging, which then wears a flat spot on the track and forces the motor to work harder. We replace worn rollers with sealed-bearing units where the gate design allows it, then adjust the track height so the gate rides level across the full travel. The photo record shows the old roller, the new roller, and the final track clearance, all in one visit.
Latch & Lock
A gate latch that will not catch is a security problem more than a convenience problem, especially on a driveway gate that is supposed to hold. We replace the latch or the strike plate, whichever has worn, and then align the gate so the latch engages without slamming or sticking. When a lock is involved, whether it is a keyed deadbolt on a walk gate or an electric lock tied to an opener board, we confirm the wiring and the strike alignment before we call the job done. Every repair includes a photo of the latch seated correctly and a written record of the part installed.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service for Gate Parts & Welding
Most of the welded steel repair work we do in Weatherford is brand-agnostic, because a cracked rail or a bent hinge bracket is a steel problem, not a motor problem. But when the work touches the opener, the brand matters. We service LiftMaster gate operators on a regular basis, including replacing the mounting brackets and welding in reinforcement plates where the operator attaches to the gate frame. LiftMaster’s residential and light commercial slide operators put a specific pull load on the gate, and if the gate steel was not factory-built for that load, we weld in the bracing to carry it.
We also work on Mighty Mule and DoorKing systems, which show up on a lot of Weatherford acreage properties and light commercial gates. Mighty Mule’s DIY-oriented openers often need a stronger bracket than the one supplied in the kit, and we weld a heavy plate in place so the arm stops flexing the gate frame. DoorKing operators are built for years of daily cycling, but the gate itself has to stay square, and when a DoorKing gate gets hit or a post shifts, the misalignment has to be corrected in steel before the limit switches will ever read correctly. Whether you have one of those brands or any other make on the property, the approach is the same: fix the steel first, then address the operator.
BeforeAfterSigns You Need Gate Parts & Welding Right Now
- The gate scrapes the driveway or leaves a mark on the concrete. A gate that makes contact with the ground is telling you the hinge side has dropped, and in Weatherford clay soil that usually means the post footing has moved. The longer it runs that way, the more the hinge barrel and the rail welds get stressed, until a hinge pin snaps or a weld cracks clean through.
- You can see daylight through a weld joint. A cracked weld is not going to heal, and it is not going to stay the same size. Every open-close cycle works the crack wider, and once it propagates across the joint the gate can drop at that corner without warning. If you can see a crack at a rail or a picket weld, that is a same-week repair, not next month.
- The gate sags at the latch side and will not seat without lifting. When you have to lift the gate to get the latch to engage, the post, the hinge, or the rail has already moved beyond adjustment range. Forcing the latch just transfers the load the wrong way and accelerates the failure.
- You feel a bump or hear a grinding sound when the gate moves. On a sliding gate, that is usually a seized roller or a bent track section, and continuing to run it wears a flat spot into the rest of the track. On a swing gate, a grinding sound is often the hinge pin binding in a bent barrel.
- The post leans more than it did last season. Weatherford’s soil expands and contracts through wet and dry cycles, and a post that moves with the soil will keep moving. A slight lean is a warning; a lean you can measure with a level is a repair waiting for the next heavy rain.
Our Gate Parts & Welding Process - Step by Step
We work the same way on a hinge replacement in Weatherford that Adrian Vance worked on commercial access-control sites starting in 2014: document first, repair second, and leave a record that the next technician, if one is ever needed, can read without guessing.
- 1
On-site inspection and measurement. We start by checking the gate’s position at both ends, the post plumb, the hinge gaps, and the weld lines, and we take photos of everything before anything is touched. If the problem is a moving post, we measure the lean and note the direction, because that tells us whether the footing has washed out or the post was undersized from the start.
- 2
Written price before any work. We hand you a flat price in writing, not a range, before we unload a single tool. That is Clause 1 of our Haven Standard, and it applies to every repair we do, from a twenty-minute latch alignment to a full post footing replacement. The price you see is the price you pay; nothing gets added at the end.
- 3
Repair with matched materials. We cut out the failed section, grind the surrounding steel clean, and weld in replacement material that is the same thickness and profile as the original so the repair does not create a new weak point. For post replacements, we pour the new footing to depth and brace the post plumb while the concrete cures.
- 4
Adjustment and cycling. After the weld or the replacement is done, we cycle the gate through its full travel several times, checking the latch engagement, the roller contact, and the operator limit positions. On an automated gate, we set the open and close limits so the motor is not pulling the gate into the end stop, which is what breaks brackets and cracks rails over time.
- 5
Documented photo record. Before we leave, you get a photo log of the failed part, the repair in progress, and the finished work, along with a written record of what was installed, what was adjusted, and the part numbers used. That is Clause 4 of the Haven Standard, and it is included on every job at no additional charge.
How Much Does Gate Parts & Welding Cost in Weatherford?
A hinge replacement on a standard Weatherford steel driveway gate typically runs $180 to $320 per hinge, depending on the gate weight and whether the mounting plate also needs to be cut out and replaced, which affects how much Gate Parts & Welding costs overall. Post replacement costs more because it involves excavation and concrete: most Weatherford post replacements land between $450 and $850, depending on the post size, the footing depth, and whether the gate has to be entirely removed and rehung. Rail repair and custom welding usually run $200 to $500 depending on the length of weld, the steel thickness, and access to the work area. Gate roller replacement for a sliding gate typically runs $120 to $260 per roller, including track adjustment. Latch and lock replacement runs $90 to $220 for most residential gates.
What moves the price is the amount of cutting and welding time, the steel thickness, and whether the gate is still on its hinges or has to be laid down for the repair. You avoid overpaying by getting a written price that already includes the labor, the material, and the adjustment, which is what we hand you before any work starts. We also offer a free second opinion on any written estimate from another company; bring the paperwork and we will review it at no cost. Call (940) 353-4158 for an exact quote. The estimate is free, and the number we quote is the number you pay.
Gate Parts & Welding Near Weatherford - Our Service Area
We run gate parts and welding service calls throughout Weatherford and into the surrounding west Fort Worth area, including Azle, White Settlement, Benbrook, and Briar. Most Weatherford calls are reached the same day, and the surrounding towns are typically one to two days out depending on scheduling. If you are in Azle or White Settlement and have a gate that is dragging or a weld that has cracked, the same written-price and photo-record process applies on every call, no matter the town.
Serving Weatherford, TX - Our Local Coverage Area
We’re based in the Weatherford area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked Questions - Gate Parts & Welding in Weatherford
Gate parts and welding is the repair of the structural steel and mechanical hardware on a gate: hinges, posts, rails, rollers, latches, and the welds that hold all of it together. It covers everything from a cracked weld joint to a full post replacement, and it is the work a gate needs before an opener can be adjusted correctly. In Weatherford, the most common welding repairs we do are rail cracks, hinge bracket replacements, and post footings that have shifted in the clay soil, similar to Gate Parts & Welding - Crowley.
Most hinge, roller, and latch replacements take one to two hours on site, including cycling the gate afterward. A post replacement takes longer, usually four to six hours, because the old footing has to be dug out and the new concrete needs time to set before the gate is rehung. We will tell you the expected time window when we hand you the written price, and we do not leave a gate hanging unsupported overnight.
Most Weatherford gate repairs fall between $120 for a basic latch replacement and $850 for a full post replacement with new concrete. Hinge replacement runs $180 to $320 per hinge, rail repair and custom welding run $200 to $500, and sliding gate rollers run $120 to $260 per roller. The price is written and handed to you before any work starts, so the estimate you get is the invoice you see when the job is done. Call (940) 353-4158 for a free estimate on your specific gate.
Yes, we service Mighty Mule, LiftMaster, DoorKing, and six other automation brands, and we work on the gate steel regardless of what motor is mounted to it. For Mighty Mule systems we often weld a heavier mounting plate in place to stop the arm from flexing the gate frame, and for LiftMaster operators we verify that the gate’s steel can carry the pull load the operator is rated for. Whatever brand is on your gate, we repair the gate itself rather than steering you toward a replacement you do not need.
In most Weatherford cases, yes. A live person answers (940) 353-4158 at any hour, and we keep same-day availability for gates that will not close or have dropped off a hinge. We will tell you over the phone whether the situation sounds like something we can stabilize the same day, and the written price still applies before any repair work begins.
Every repair we complete is covered by our 365-Day Done Right Promise. If the repair is not right within one year, we make it right at no additional charge. The promise covers the repair itself, and the written record we leave on every job shows exactly what was done, so if any question comes up about the work, the documentation is already in your hands.
Clear the gate’s travel path so the gate can open and close fully, and make sure we have access to both sides of the gate. If the gate is automated, leave the power connected so we can cycle it after the repair; if the gate is completely off its hinges, block it securely and tell us on the phone when you call. You do not need to remove anything or have tools ready, we bring what the job needs.
Schedule Your Gate Parts & Welding Service in Weatherford Today
If your gate is dragging, sagging, or coming apart at a weld, call (940) 353-4158 and tell us what you are seeing. We will give you a straight answer, a written price, and a time we can be there. No obligation, no pressure, and a live person on the phone any hour of the day or night.
Written by Adrian Vance, Owner at Vance Gate Repair, serving Weatherford since 2014.