Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Watauga, TX
Gate access control and gate parts repair in Watauga come down to one recurring problem: gates built in the 1970s through 1990s that have spent 30 to 50 years fighting North Texas clay soil. The ground moves, the posts lean, the frame twists, and suddenly the opener won’t close, the keypad mount pulls loose, or the hinge tears out of the post. We quote every repair in writing before any work begins, and we leave a photo record of what we found and what we fixed. Call (940) 353-4158 when your gate stops doing what it’s supposed to.
Why Watauga Homes Are Different
Watauga is a fully built-out, landlocked Tarrant County suburb. Most residential lots were developed between the late 1960s and the 1990s, and nearly every home has a cedar or pine privacy fence gate along the side yard. Those gates are now 30 to 50 years old, and the original hardware – hinges, latches, post anchors – is frequently corroded or outright failing.
The bigger issue is the soil. Tarrant County’s expansive black clay swells during wet winters and springs, then contracts and cracks in the summer drought. Each cycle tilts and heaves fence posts a little more. A gate that dragged in March may swing freely by August, then drag again the following spring. Any repair on a Watauga gate has to account for that seasonal movement, or we’ll be back fixing the same post next year. Townhome and HOA communities across Watauga face the same cycle, which is why we always document the post setting and gate alignment before we leave.
Our Main Watauga Services
Most Watauga homeowners call us for three things: a gate that won’t swing or latch, a new gate for a fence that’s reached the end of its life, and an opener that quit halfway through the year.
Gate Repair in Watauga
Sagging frames, seized hinges, latches that no longer catch, posts leaning far enough that the gate drags across the concrete – those are the bread-and-butter calls in Watauga. Most wood privacy gates on the original posts have shifted over decades of clay movement, and a repair that only replaces the hardware without addressing the post lean will fail again. We re-set or re-plumb the post, replace the corroded hardware, and photograph the finished alignment so the record shows exactly what was done. Gate Repair in Watauga covers the full scope of that work.
Gate Installation in Watauga
When a Watauga fence gate has split, rotted, or twisted beyond repair, replacement usually makes more sense than another patch job. We install new wood frame gates matched to the existing fence height and style, set posts in concrete with a footer deep enough to resist the clay movement, and mount the gate so it clears the ground through wet and dry seasons. A new gate in Watauga should be built for the soil it stands in, not just measured to the opening. Gate Installation in Watauga walks through materials, sizing, and what the job includes.
Gate Motor & Opener in Watauga
Watauga’s swing gates often have an opener that was added years after the gate was built, and the original post wasn’t poured for an operator arm pulling against it. When the post flexes, the opener binds, the limit settings drift, and the motor burns out faster. We service all nine major automation brands – LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule – so we repair the motor already on the property rather than pushing a replacement. Gate Motor & Opener in Watauga covers diagnostics, repairs, and full operator replacements.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterGate Access Control in Watauga
Gate access control in Watauga means keypads, remotes, card readers, phone entry, and video intercoms for the side-yard gates, driveway gates, and small community gates common to this suburb’s 1970s-through-1990s housing stock. The recurring failure here is environmental: Watauga’s wet-dry clay cycle shifts gate posts every year, which pulls keypad wires loose, throws photo-eyes out of alignment, and breaks the electrical continuity on old field splices. Our service includes a written price before the first part is ordered and a photo record of every connection we touch. That’s the same documentation habit we bring to Gate Access Control jobs everywhere.
Keypad Entry
Signs you need it
The keypad weatherproof cover has cracked, water has gotten inside, the buttons are unresponsive after rain, or the gate opens intermittently after you type the code.
What it costs in Watauga
Replacing a residential gate keypad in Watauga typically runs $145-$320 installed, depending on whether we can reuse the existing wiring or need to run a new low-voltage line to a post that has shifted.
How we do it
We remove the old keypad, inspect the wiring and connections for corrosion, mount the new unit, set the codes, and photograph the finished install plus the wiring at the junction.
Phone Entry
Signs you need it
You want visitors to call your phone from the gate instead of carrying a remote, or the existing phone-entry unit will not dial out or the call audio has become unusable.
What it costs in Watauga
A phone-entry system for a Watauga driveway gate typically runs $380-$750 installed, including the unit, SIM card or landline hookup, and programming to route calls to your phone.
How we do it
We install the entry unit at the gate, connect it to the operator’s control board, program the phone number routing, and test it with a live call before we leave.
What Gate Access Control Costs in Watauga
| Item | Typical range in Watauga |
|---|---|
| Keypad replacement | $145-$320 installed |
| Phone entry system | $380-$750 installed |
| Photo-eye realignment | $95-$185 per visit |
Can you fix my gate keypad without replacing the whole system?
Usually yes. Many Watauga keypad failures are corroded wire splices or water-damaged seals, not a dead control board. We diagnose the actual fault first, quote in writing, and replace only what’s failed.
Will my access control still work when the gate post shifts?
The electronics can keep working if the wiring has enough slack and the photo-eye is re-aimed after the movement settles. We re-aligned beams and leave enough service loop to absorb the clay cycle. Call (940) 353-4158 for an exact assessment.
Gate Parts & Welding in Watauga
Gate parts and welding in Watauga are mostly about the wood-frame gates on 30-to-50-year-old ranch homes where the original hardware has corroded and the post has moved. Hinges tear out, latch bars bend, the gate frame sags until it drags, and the post itself has often been pushed several inches out of plumb by the shrink-swell clay. We fabricate, weld, and replace the steel components while accounting for the ground they’re attached to. Every Gate Parts & Welding job here gets a written price and a photo record of what was installed.
Hinge Replacement
Signs you need it
The gate sags on its hinge side, the top hinge screws have pulled out of the post, or you can lift the gate up and see the hinge leaves move independently.
What it costs in Watauga
Hinge replacement on a Watauga wood gate typically runs $120-$260 per hinge, including the new heavy-duty hardware and shimming the gate back to square in the opening.
How we do it
We remove the failed hinge, fill and re-drill the mounting holes, install a heavier hinge with longer lag screws, and re-hang the gate with the correct reveal.
Post Replacement
Signs you need it
The gate post visibly leans, the gate drags in wet months but frees up in August, or the post has cracked at ground level and the gate sways laterally.
What it costs in Watauga
Replacing a steel or wood gate post in Watauga runs $280-$540 per post, including digging out the old footer, setting the new post in concrete, and re-hanging the gate.
How we do it
We dig out the old post and footer, set the new post in concrete at a deeper depth for the clay conditions, brace it plumb while concrete cures, then re-hang the gate and photograph the result.
What Gate Parts & Welding Costs in Watauga
| Item | Typical range in Watauga |
|---|---|
| Hinge replacement | $120-$260 per hinge |
| Post replacement | $280-$540 per post |
| Custom steel weld repair | $140-$330 per section |
Can you weld a cracked gate frame without replacing the whole gate?
Yes, in most cases. We can weld a cracked steel frame or reinforce a split wood frame with steel plate and strapping. The repair is documented with photos and the price is written before we start.
How long will a replaced post stay plumb in Watauga clay?
A properly set post with a deeper concrete footer and gravel base typically resists the wet-dry cycle far longer than the original shallow 1970s footer did. We always photograph the footer depth before backfilling. Call (940) 353-4158 for specifics on your post.
Brands We Service in Watauga
We work on LiftMaster, FAAC, BFT, Mighty Mule, Viking, Ghost Controls, DoorKing, Linear, and Elite systems. Our techs carry common circuit boards, limit switches, and remote transmitters in the truck, so many Watauga opener repairs are same-day. See our brands for the full list of automation systems we service.
Pricing for Gate Repair in Watauga, TX
| Service | Typical range in Watauga |
|---|---|
| Keypad replacement | $145-$320 installed |
| Phone entry system | $380-$750 installed |
| Photo-eye realignment | $95-$185 per visit |
| Hinge replacement | $120-$260 per hinge |
| Post replacement | $280-$540 per post |
| Custom steel weld repair | $140-$330 per section |
| Gate opener repair (service call + labor) | $110-$220 per visit |
| Swing gate motor replacement | $480-$950 depending on brand |
| Slide gate motor replacement | $620-$1,200 depending on brand |
| Limit switch adjustment | $85-$165 per visit |
Prices in Watauga push toward the upper end of each range when the gate post has moved enough to require re-plumbing before the part can be installed, or when the original 1970s wiring has corroded and must be replaced. Whatever the number is, it’s written down and handed to you before any work starts. That’s the whole point of our pricing system.
Neighborhoods We Serve in Watauga
We respond to gate repair calls across all of Watauga, including the older ranch-home subdivisions and the townhome communities with shared gates. Typical response for a repair call in this area is within one business day.
- Whitley Road neighborhoods
- Browning Drive area
- Hightower Drive corridor
- Starnes Road subdivisions
- Watauga Commons and nearby townhome communities
Service Area - Cities Near Watauga
Our crews serve Watauga and the surrounding Tarrant County suburbs from our Dallas-Fort Worth dispatch office. If you’re in a neighboring city, we cover those as well: Weatherford, TX, Azle, TX, White Settlement, TX, and Benbrook, TX.
Serving Watauga, TX - Our Local Coverage Area
We’re based in the Watauga area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Watauga
For a fence gate repair on an existing fence, Watauga generally does not require a separate permit. New driveway gate installations with an automatic opener may require an electrical permit depending on the run and the operator. We confirm the current requirement before we start any job and handle the electrical work to code.
Most Watauga repair calls are scheduled within one business day, and we answer the phone live 24/7. If a gate is stuck open and the property is unsecured, we treat it as a priority and get a tech routed as soon as one is available. Call (940) 353-4158 and you’ll talk to a person, not a voicemail.
We can give you a price range for common jobs like hinge or keypad replacement. The exact written price comes after we see the gate, the post condition, and the wiring. What we never do is start the work without handing you a written number first. No surprises on the invoice.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Watauga Customers Say
"They installed the opener and left me a diagram of the wiring and the limit settings. When I needed a second remote programmed I could do it myself."
- Nadine C."Our gate was hit by a delivery truck. They came out, documented the damage properly for the insurer, and the claim went through without an argument."
- Camille R."Honest about what did not need doing. Told me the operator had years left and only the control board needed replacing."
- Douglas N.